Jackson Dishwasher Tempstar S User Manual
TEMPSTAR SERIES UPRIGHT DOOR DISHMACHINES  
INSTALLATION/OPERATION  
& TECHNICAL MANUAL  
ELECTRICALLY HEATED MODELS:  
TEMPSTAR  
TEMPSTAR LT  
TEMPSTAR NB  
STEAM HEATED MODELS:  
TEMPSTAR S  
Jackson MSC, LLC.  
P.O. BOX 1060  
HWY. 25E  
BARBOURVILLE, KY. 40906  
PHONE (606) 523-9795  
FAX (606) 523-9196  
www.jacksonmsc.com  
July 24, 2009  
P/N 7610-003-61-42 D  
 
MANUFACTURERS WARRANTY  
ONE YEAR LIMITED PARTS & LABOR WARRANTY  
ALL NEW JACKSON DISHWASHERS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM  
DEFECTS IN MATERIAL OR WORKMANSHIP, UNDER NORMAL USE AND OPERATION FOR A PERIOD OF (1) ONE  
YEAR FROM THE DATE OF PURCHASE, BUT IN NO EVENT TO EXCEED (18) EIGHTEEN MONTHS FROM THE DATE  
OF SHIPMENT FROM THE FACTORY.  
Jackson MSC agrees under this warranty to repair or replace , at its discretion, any original part which fails under normal use due to faulty  
material or workmanship during the warranty period, providing the equipment has been unaltered, and has been properly installed, main-  
tained and operated in accordance with the applicable factory instruction manual furnished with the machine and the failure is reported to  
the authorized service agency within the warranty period. This includes the use of factory specified genuine replacement parts, purchased  
directly from a Jackson authorized parts distributor or service agency. Use of generic replacement parts may create a hazard and void war-  
ranty certification.  
The labor to repair or replace such failed part will be paid by Jackson MSC, within the continental United States, Hawaii and Canada, during  
the warranty period provided a Jackson MSC authorized service agency, or those having prior authorization from the factory, performs the  
service. Any repair work by persons other than a Jackson MSC authorized service agency is the sole responsibility of the customer. Labor  
coverage is limited to regular hourly rates, overtime premiums and emergency service charges will not be paid by Jackson MSC.  
Accessory components not installed by the factory carry a (1) one year parts warranty only. Accessory components such as table limit switch-  
es, pressure regulators, pre rinse units, etc. that are shipped with the unit and installed at the site are included. Labor to repair or replace  
these components is not covered by Jackson MSC.  
This warranty is void if failure is a direct result from shipping, handling, fire, water, accident, misuse, acts of god, attempted repair by unau-  
thorized persons, improper installation, if serial number has been removed or altered, or if unit is used for purpose other than it was origi-  
nally intended.  
TRAVEL LIMITATIONS  
Jackson MSC limits warranty travel time to (2) two hours and mileage to (100) one hundred miles. Jackson MSC will not pay for travel time  
and mileage that exceeds this, or any fees such as those for air or boat travel without prior authorization.  
WARRANTY REGISTRATION CARD  
The warranty registration card supplied with the machine must be returned to Jackson MSC within 30 days to validate the warranty.  
REPLACEMENT PARTS WARRANTY  
Jackson replacement parts are warranted for a period of 90 days from the date of installation or 180 days from the date of shipment from the  
factory, which ever occurs first.  
PRODUCT CHANGES AND UPDATES  
Jackson MSC reserves the right to make changes in design and specification of any equipment as engineering or necessity requires.  
THIS IS THE ENTIRE AND ONLY WARRANTY OF JACKSON MSC. JACKSON’S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING  
NEGLIGENCE, WITH RESPECT TO THE GOODS OR SERVICES COVERED HEREUNDER, SHALL IN NO CASE EXCEED THE PRICE  
OF THE GOODS OR SERVICES OR PART THEREOF WHICH GIVES RISE TO THE CLAIM.  
THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING FOR FITNESS OR MERCHANTABILITY, THAT ARE NOT SET  
FORTH HEREIN, OR THAT EXTEND BEYOND THE DURATION HEREOF. UNDER NO CIRCUMSTANCES WILL JACKSON MSC BE  
LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, OR FOR THE DAMAGES IN THE NATURE OF PENALTIES,  
ARISING OUT OF THE USE OR INABILITY TO USE ANY OF ITS PRODUCTS.  
ITEMS NOT COVERED  
This warranty does not cover cleaning or deliming of the unit or any component such as, but not limited to, wash arms, rinse arms or strain-  
ers at anytime. Nor does it cover adjustments such as, but not limited to timer cams, thermostats or doors, beyond 30 days from the date  
of installation. In addition, the warranty will only cover the replacement of wear items such as curtains, drain balls, door guides or gaskets  
during the first 30 days after installation. Also, not covered are conditions caused by the use of incorrect (non-Commercial) grade detergents,  
incorrect water temperature or pressure, or hard water conditions.  
i
 
STOP!  
PARE!  
ARRET!  
CALL 1-888-800-5672 TO REGISTER THIS PRODUCT!  
FAILURE TO DO SO WILL VOID THE WARRANTY!  
LLAME AL 1-888-800-5672 PARA REGISTRAR ESTE PRODUCTO!  
AL NO HACERLO LA GARANTIA SERA ANULADA!  
S.V.P. APPELER 1-888-800-5672 POUR ENREGISTRER CE PRODUIT,  
LA GARANTIE SERA ANNULEE POUR TOUT PRODUIT NON- ENREGISTREE  
ii  
 
REVISION  
DATE  
MADE APPLICABLE  
REVISION  
DETAILS  
BY  
ECN  
A
B
C
D
11/11/08  
ARL  
8045  
Released to production.  
Added new NSF rating.  
04/22/2009  
06/22/2009  
07/24/2009  
ARL  
JC  
8094  
8114  
8104  
Removed NSF Rating from steam heated unit.  
ARL  
Added information regarding electrical field conversion.  
iii  
 
NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL  
TEMPSTAR = Electrically heated, high temp, hot water sanitizing, with booster heater, door-type dish-  
machine  
TEMPSTAR LT = Electrically heated, low temp, chemical sanitizing, no rinse booster, door-type dish-  
machine  
TEMPSTAR NB = Electrically heated, high temp, hot water sanitizing, no rinse booster, door-type dish-  
machine  
TEMPSTAR S = Steam heated, high temp, hot water sanitizing, door-type dishmachine  
Jackson MSC LLC. provides technical support for all  
of the dishmachines detailed in this manual. We  
strongly recommend that you refer to this manual  
before making a call to our technical support staff.  
Model:  
Serial No.:  
Please have this manual with you when you call so  
that our staff can refer you, if necessary, to the prop-  
er page. Technical support is available from 8:00  
a.m. to 5:00 p.m. (EST), Monday through Friday.  
Technical support is not available on holidays.  
Contact technical support toll free at 1-888-800-  
5672. Please remember that technical support is  
available for service personnel only.  
Installation Date:  
Service Rep. Name:  
Phone No.:  
iv  
 
TABLE OF CONTENTS  
Section  
I.  
Description  
Page  
Specifications  
Operating Capacities  
Electrical Requirements  
Dimensions Tempstar/Tempstar LT/Tempstar NB (Top Mounted Control Box)  
Table Dimensions  
2
3
4
5
II.  
Installation/Operation Instructions  
Installation Instructions  
7
8
9
Electrical Installation Instructions  
Operation Instructions  
Detergent Control  
False Panel Installation  
10  
11  
III.  
IV.  
V.  
Preventative Maintenance  
Troubleshooting Section  
12  
14  
Drawing/Parts Section  
Top Mounted Control Box Assembly (Universal Timer)  
Hood Assembly (Bolted Single Support Design)  
Cantilever Arm/Door Assemblies  
Tub Assembly  
Steam Tub Assembly  
Frame Assembly  
Rinse Tank Assembly  
Coil Assembly  
Incoming Steam Plumbing Assembly  
Wash Motors  
Motor & Pump Assembly  
Wash Heaters/Rinse Heaters  
Incoming Plumbing/Outlet Plumbing Assembly  
WPRK Kit Option  
Tempstar LT & Tempstar NB Incoming Plumbing Assembly  
1/2” Solenoid Valve & 1/2” NPT Vacuum Breaker Repair Parts Kits  
Wash and Rinse Arm/Manifold Assemblies  
18  
20  
21  
23  
25  
27  
28  
30  
31  
32  
33  
34  
36  
37  
38  
39  
40  
Safety Door Interlock (SDI)/Exhaust Fan Control/Transformer Mounting Box Components 42  
False Panel Installation  
GO*BOX Kit  
Drain Quench Assembly  
43  
44  
45  
v
 
TABLE OF CONTENTS  
VI.A  
Electrical Diagrams - Top Mounted Control Boxes  
Tempstar (UT w/Cycle Switches) 208 - 230V, 50/60 Hz, single/three phase  
Tempstar (UT w/Cycle Switches) 460V, 60 Hz, three phase  
Tempstar LT & NB (UT w/Cycle Switches) 208 - 230V, 50/60 Hz, single/three phase  
Tempstar LT & NB (UT w/Cycle Switches) 460V, 60 Hz, three phase  
Tempstar S (Universal Timer) 208 - 230V, 60 Hz, single/three phase  
47  
48  
49  
50  
51  
VI.C  
VII.  
Electrical Diagram Options  
Safety Door Interlock (SDI)  
Drain Quench  
53  
54  
54  
Exhaust Fan Control  
Jackson Maintenance & Repair Centers  
55  
vi  
 
SECTION 1:  
SPECIFICATION INFORMATION  
1
 
SECTION 1: SPECIFICATION INFORMATION  
OPERATING CAPACITIES  
WATER REQUIREMENTS  
PERFORMANCE/CAPABILITIES  
TEMPSTAR:  
OPERATING CAPACITY:  
(HIGH TEMPERATURE)  
RACKS PER HOUR  
DISHES PER HOUR  
GLASSES PER HOUR  
WASH TEMPERATURE (MINIMUM)(°F)  
WASH TEMPERATURE (MINIMUM)(°C)  
RINSE TEMPERATURE (MINIMUM)(°F)  
RINSE TEMPERATURE (MINIMUM)(°C)  
INLET WATER TEMPERATURE:  
12KW RINSE HEATER (°F)  
150  
66  
180  
83  
58  
1450  
1450  
(LOW TEMPERATURE)  
RACKS PER HOUR  
DISHES PER HOUR  
GLASSES PER HOUR  
140  
60  
110  
44  
50  
1250  
1250  
12KW RINSE HEATER (°C)  
14KW RINSE HEATER (°F)  
14KW RINSE HEATER (°C)  
FLOW PRESSURE (PSI)  
10  
WATER LINE SIZE (NPT)  
DRAIN LINE SIZE (NPT)  
1/2”  
1 1/2”  
OPERATING CYCLE (SECONDS):  
MINIMUM (OTHER CYCLE TIMES ARE AVAILABLE)  
(HIGH TEMPERATURE)  
TEMPSTAR LT:  
WASH TIME  
40  
RINSE TIME  
DWELL TIME  
TOTAL CYCLE TIME  
13  
4
57  
WASH TEMPERATURE (MINIMUM)(°F)  
WASH TEMPERATURE (MINIMUM)(°C)  
RINSE TEMPERATURE (MINIMUM)(°F)  
RINSE TEMPERATURE (MINIMUM)(°C)  
INLET WATER TEMPERATURE (°F)  
INLET WATER TEMPERATURE (°C)  
FLOW PRESSURE (PSI)  
WATER LINE SIZE (NPT)  
DRAIN LINE SIZE (NPT)  
MINIMUM CHLORINE REQUIRED (PPM)  
130  
55  
130  
55  
130  
55  
10  
1/2”  
1 1/2”  
50  
(LOW TEMPERATURE)  
WASH TIME  
RINSE TIME  
DWELL TIME  
TOTAL CYCLE TIME  
45  
11  
10  
66  
TANK CAPACITY:  
TEMPSTAR NB/TEMPSTAR S:  
WASH TANK (GAL)  
8.0  
WASH TANK (L)  
RINSE TANK (TEMPSTAR) (GAL)  
RINSE TANK (TEMPSTAR) (L)  
30.3  
3.0  
11.4  
WASH TEMPERATURE (MINIMUM)(°F)  
WASH TEMPERATURE (MINIMUM)(°C)  
RINSE TEMPERATURE (MINIMUM)(°F)  
RINSE TEMPERATURE (MINIMUM)(°C)  
INLET WATER TEMPERATURE (°F)  
INLET WATER TEMPERATURE (°C)  
FLOW PRESSURE (PSI)  
150  
66  
180  
83  
180  
83  
10  
STEAM REQUIREMENTS:  
COIL SIZE  
STEAM FLOW PRESSURE (P.S.I.)  
CONSUMPTION @ 15 P.S.I. (LBS/HR)  
3/4”  
10-20  
45  
WATER LINE SIZE (NPT)  
DRAIN LINE SIZE (NPT)  
1/2”  
1 1/2”  
ELECTRICAL REQUIREMENTS  
WASH MOTOR HP  
3/4  
NOTE: Always refer to the machine data plate for specific  
electrical and water requirements. The material provided  
on this page is for reference only and may be subject to  
change without notice.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: 04/22/2009  
2
 
SECTION 1: SPECIFICATION INFORMATION  
ELECTRICAL REQUIREMENTS  
NOTE: Typical Electrical Circuit is based upon (1) 125% of the full amperage load of the machine and (2) typical  
fixed-trip circuit breaker sizes as listed in the NEC 2002 Edition. Local codes may require more stringent protection  
than what is displayed here. Always verify with your electrical service contractor that your circuit protection is ade-  
quate and meets all applicable national and local codes. These numbers are provided in this manual simply for ref-  
erence and may change without notice at any given time.  
TEMPSTAR:  
TEMPSTAR LT/TEMPSTAR NB:  
RINSE  
HEATER  
RATINGS  
12KW@240V  
14KW@240V  
12KW@240V  
14KW@240V  
TYPICAL  
TOTAL ELECTRICAL  
AMPS CIRCUIT  
RINSE  
HEATER  
RATINGS  
N/A  
N/A  
TYPICAL  
TOTAL ELECTRICAL  
VOLTS PH  
HZ  
50  
50  
50  
50  
VOLTS PH  
HZ  
50  
50  
AMPS  
28 A  
30 A  
CIRCUIT  
35 AMP  
40 AMP  
208  
208  
230  
230  
1
1
1
1
71 A  
78 A  
78 A  
86 A  
90 AMP  
208  
230  
1
1
100 AMP  
100 AMP  
110 AMP  
208  
230  
380  
415  
440  
3
3
3
3
3
50  
50  
50  
50  
50  
N/A  
N/A  
N/A  
N/A  
N/A  
20 A  
21 A  
10 A  
10 A  
8 A  
25 AMP  
30 AMP  
15 AMP  
15 AMP  
15 AMP  
208  
208  
230  
230  
380  
380*  
415  
415  
440  
440  
3
3
3
3
3
3
3
3
3
3
50  
50  
50  
50  
50  
50  
50  
50  
50  
50  
12KW@240V  
14KW@240V  
12KW@240V  
14KW@240V  
12KW@380V  
14KW@208V  
12KW@415V  
14KW@415V  
12KW@460V  
14KW@460V  
45 A  
49 A  
48 A  
53 A  
29 A  
34 A  
26 A  
29 A  
21 A  
25 A  
60 AMP  
70 AMP  
60 AMP  
70 AMP  
40 AMP  
45 AMP  
35 AMP  
40 AMP  
30 AMP  
35 AMP  
208  
230  
1
1
60  
60  
N/A  
N/A  
26 A  
28 A  
35 AMP  
35 AMP  
208  
230  
460  
3
3
3
60  
60  
60  
N/A  
N/A  
N/A  
18 A  
28 A  
8 A  
25 AMP  
35 AMP  
15 AMP  
208  
208  
230  
230  
1
1
1
1
60  
60  
60  
60  
12KW@240V  
14KW@240V  
12KW@240V  
14KW@240V  
69 A  
76 A  
76 A  
84 A  
90 AMP  
100 AMP  
100AMP  
110 AMP  
TEMPSTAR S:  
RINSE  
HEATER  
RATINGS  
N/A  
TYPICAL  
TOTAL ELECTRICAL  
VOLTS PH  
HZ  
60  
60  
AMPS  
6 A  
6 A  
CIRCUIT  
15 AMP  
15 AMP  
208  
208  
230  
230  
460  
460  
3
3
3
3
3
3
60  
60  
60  
60  
60  
60  
12KW@240V  
14KW@240V  
12KW@240V  
14KW@240V  
12KW@480V  
14KW@480V  
43 A  
47 A  
46 A  
51 A  
22 A  
25 A  
60 AMP  
60 AMP  
60 AMP  
70 AMP  
30 AMP  
35 AMP  
208  
230  
1
1
N/A  
208  
230  
3
3
60  
60  
N/A  
N/A  
6 A  
6 A  
15 AMP  
15 AMP  
* This model is wired in a wye configuration for the heaters.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
3
 
SECTION 1: SPECIFICATION INFORMATION  
DIMENSIONS TEMPSTAR/NB/LT/S (TOP MOUNTED CONTROL BOX)  
A- WATER INLET (1/2” NPT)  
B- ELECTRICAL CONNECTION POINT  
C- DRAIN (1 1/2” NPT)  
D- STANDARD CLEARANCE BETWEEN  
MACHINE AND WALL (WITH DISHTABLE) IS 4” (10.2 cm).  
LEGEND  
D
D
4 7/8” (12.4 cm)  
B
25 1/4” (64.1 cm)  
32” (81.3 cm)  
B
A
76” (193 cm)  
W/ DOOR OPEN  
17 1/2”  
(44.5 cm)  
MACHINE  
OPENING  
60 5/8”  
(154 cm)  
61 3/4”  
(156.8 cm)  
WATER  
64 3/8”  
(163.5 cm)  
INLET TO  
FLOOR  
34” (86.4 cm)  
TABLE  
HEIGHT  
14”  
(35.6 cm)  
DRAIN  
TO  
FLOOR  
C
15 1/2” (39.4 cm)  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
4
 
SECTION 1: SPECIFICATION INFORMATION  
TABLE DIMENSIONS  
4” (10.2 cm)  
MINIMUM  
TABLE DIMENSIONS  
CORNER INSTALLATION  
20 1/2” (52.1 cm)  
OPENING  
2 1/2” (6.4 cm)  
25 1/4”  
(64.1 cm)  
4” (10.2 cm)  
MINIMUM  
3/4” (1.9 cm)  
1 1/2” (3.81 cm) ROLL  
TABLE DIMENSIONS  
CONNECTION TO DISHMACHINE  
20 1/2” (52.1 cm)  
4” (10.2 cm)  
MINIMUM  
TABLE DIMENSIONS  
STRAIGHT THROUGH INSTALLATION  
25 1/4” (64.1 cm)  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
5
 
SECTION 2:  
INSTALLATION/OPERATION  
INSTRUCTIONS  
6
 
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS  
INSTALLATION INSTRUCTIONS  
VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi-  
cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away  
the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged  
condition. However, rough handling by carriers or others may result in there being damage to the unit while in transit. If such a sit-  
uation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to  
inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of receiving the  
machine. Also, contact the dealer through which you purchased the unit.  
UNPACKING THE DISHMACHINE: Once the machine has been removed from the container, ensure that there are no missing  
parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson immediately to  
have the missing item shipped to you.  
LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is  
important to prevent any damage to the machine during operation and to ensure the best results  
when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of  
channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to  
side and from front to back before making any connections.  
Raise  
Lower  
Frame with Adjustable Foot  
PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicable local, state, and national plumbing  
codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any com-  
ponent of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the  
valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses  
resulting from this fouling, are not the responsibility of the manufacturer.  
CONNECTING THE DRAIN LINE: The drain for the Tempstar models covered in this manual are gravity discharge drains. All pip-  
ing from the 1 1/2” FNPT connection on the wash tank must be pitched (1/4” per foot) to the floor or sink drain. All piping from the  
machine to the drain must be a minimum 1 1/2” I.P.S. and shall not be reduced. There must also be an air gap between the machine  
drain line and the floor sink or drain. If a grease trap is required by code, it should have  
a flow capacity of 5 gallons per minute.  
WATER SUPPLY CONNECTION: Ensure that you have read the section entitled  
“PLUMBING THE DISHMACHINE” above before proceeding. Install the water supply  
line (1/2” pipe size minimum) to the dishmachine line strainer using copper pipe. It is  
recommended that a water shut-off valve be installed in the water line between the  
main supply and the machine to allow access for service.  
The water supply line is to be capable of 10 PSI “flow” pressure at the recommended  
temperature indicated on the data plate.  
In areas where the water pressure fluctuates or is greater than the recommended pres-  
sure, it is suggested that a water pressure regulator be installed. The Tempstar models  
covered in this manual come with water pressure regulators as standard equipment.  
Incoming Plumbing Y-strainer Connection  
Please notify Jackson immediately if this component is not present on your machine.  
Do not confuse static pressure with flow pressure. Static pressure is the line pressure in a “no flow” condition (all valves and ser-  
vices are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.  
It is also recommended that a shock absorber (not supplied with the Tempstar model) be installed in the incoming water line. This  
prevents line hammer (hydraulic shock), induced by the solenoid valve as it operates, from causing damage to the equipment.  
STEAM LINE CONNECTION: The steam machines come with lines by which the source steam needs to be connected. Connect  
all steam lines to the machine as all applicable codes provide. See machine data plate for information concerning steam flow pres-  
sure.  
CHEMICAL DISPENSING EQUIPMENT: The Tempstar LT machine requires that a separate chemical feeder be connected to it to  
provide the required detergent and sanitizer. This feeder needs to be able to operate against a head of 25 PSI and provide 1.79  
ml of a 10% Chlorine sanitizer per minute.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
7
 
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS  
INSTALLATION INSTRUCTIONS (CONTINUED)  
PLUMBING CHECK: Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been  
installed. Check for any leaks and repair as required. All leaks must be repaired prior to placing the machine in operation.  
ELECTRICAL POWER CONNECTION: Electrical and grounding connections must  
comply with the applicable portions of the National Electrical Code ANSI/NFPA 70  
(latest edition) and/or other electrical codes.  
Power Block  
Ground Lug  
Disconnect electrical power supply and place a tag at the disconnect switch to indi-  
cate that you are working on the circuit.  
The dishmachine data plate is located on the right side and to the front of the  
machine. Refer to the data plate for machine operating requirements, machine volt-  
age, total amperage load and serial number.  
To install the incoming power lines, open the control box. This will require taking a  
phillipshead screwdriver and removing the four (4) screws on the front cover of the  
control box. Install 3/4” conduit into the pre-punched holes in the back of the con-  
trol box. Route power wires and connect to power block and grounding lug. Install  
the service wires (L1, L2, and L3 (3 phase only)) to the appropriate terminals as  
they are marked on the terminal block. Install the grounding wire into the lug pro-  
vided. Tighten the connections. It is recommended that “DE-OX” or another similar  
anti-oxidation agent be used on all power connections.  
Incoming Power Connection  
VOLTAGE CHECK: Ensure that the power switch is in the OFF position and  
apply power to the dishmachine. Check the incoming power at the terminal block and ensure it corresponds to the voltage list-  
ed on the data plate. If not, contact a qualified service agency to examine the problem. Do not run the dishmachine if the volt-  
age is too high or too low. Shut off the service breaker and mark it as being for the dishmachine. Advise all proper personnel  
of any problems and of the location of the service breaker. Replace the control box cover and tighten down the screws.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
8
 
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS  
OPERATION INSTRUCTIONS  
PREPARATION: Before proceeding with the start-up of the unit, verify the following:  
1. The pan strainer and pump suction strainer are in place and are clean.  
2. The overflow tube and o-ring are installed.  
3. That the wash and rinse arms are screwed securely into place and that their endcaps are tight. The wash and rinse  
arms should rotate freely.  
POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified  
as being correct. If not, the voltage will have to be verified.  
FILLING THE WASH TUB: Ensure that the delime switch is in the NORMAL position, and place the power switch into the ON  
position. The Tempstar should fill automatically and shut off when the appropriate level is reached (just below the pan strain-  
er). Verify that the drain stopper is preventing the wash tub water from leaking excessively. There may be some slight leakage  
from the drain hole. Verify that there are no other leaks on the unit before proceeding any further. The wash tub must be com-  
pletely filled before operating the wash pump to prevent damage to the component. Once the wash tub is filled, the unit is ready  
for operation.  
WARE PREPARATION: Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware  
may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine  
is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether  
of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are  
good ideas, especially for silverware and casserole dishes. Place cups and glasses upside down in racks so that they do not  
hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria  
that could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.  
DAILY MACHINE PREPARATION: Refer to the section entitled “PREPARATION” at the top of this page and follow the instruc-  
tions there. Afterwards, check that all of the chemical levels are correct and/or that there is plenty of detergent available for the  
expected workload.  
WARM-UP CYCLES: For a typical daily start-up, it may be necessary to run the machine through 3 cycles to ensure that all of  
the cold water is out of the system and to verify that the unit is operating correctly. To cycle the machine, ensure that the power  
is on and that the tub has filled to the correct level. Lift the doors and the cycle light will illuminate. When the light goes out,  
close the doors, the unit will start, run through the cycle, and shut off automatically. Repeat this two more times. The unit should  
now be ready to proceed with the washing of ware.  
WASHING A RACK OF WARE: To wash a rack, open the doors completely (being careful for hot water that may drip from the  
doors) and slide the rack into the unit.  
Close the doors and the unit will start automatically. Once the cycle is completed, open the door (again watching for the drip-  
ping hot water) and remove the rack of clean ware. Replace with a rack of soiled ware and close the doors. The process will  
then repeat itself.  
OPERATIONAL INSPECTION: Based upon usage, the pan strainer may become clogged with soil and debris as the workday  
progresses. Operators should regularly inspect the pan strainer to ensure it has not become clogged. If the strainer does, it will  
reduce the washing capability of the machine. Instruct operators to clean out the pan strainer at regular intervals or as required  
by work load.  
SHUTDOWN AND CLEANING: At the end of the workday, close the doors. When the unit completes the cycle, turn the power  
switch to the OFF position and open the doors. Remove and clean the pan strainer. Remove the drain stopper from the tub and  
allow the tub to drain (NOTE: the wash tank water will be hot so caution is advised). Once the wash tub is drained, remove the  
pump suction strainer. Remove soil and debris from the strainer and set to the side. Unscrew the wash and rinse arms from  
their manifolds. Remove the endcaps and flush the arms with water. Use a brush to clean out the inside of the arms. If the noz-  
zles appear to be clogged, use a toothpick to remove the obstruction. Wipe the inside of the unit out, removing all soil and  
scraps. Reassembly the wash and rinse arms and replace them in the unit. The arms only need to be hand tight, do not use  
tools to tighten them down. Reinstall the drain stopper and strainers and close the doors.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
9
 
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS  
DETERGENT CONTROL  
Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate.  
Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment spe-  
cialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll  
understand what they are talking about.  
First, you must understand that hard water greatly effects the performance of the dishmachine. Water hardness is the amount  
of dissolved calcium and magnesium in the water supply. The more dissolved solids in the water, the greater the water hard-  
ness. Hard water works against detergent, thereby causing the amount of detergent required for washing to increase. As you  
use more detergent, your costs for operating the dishmachine will increase and the results will decrease. The solids in hard  
water also may build-up as a scale on wash and rinse heaters, decreasing their ability to heat water. Water temperature is  
important in removing soil and sanitizing dishes. If the water cannot get hot enough, your results may not be satisfactory. This  
is why Jackson recommends that if you have installed the machine in an area with hard water, that you also install some type  
of water treatment equipment to help remove the dissolved solids from the water before it gets to the dishmachine.  
Second, hard water may have you adding drying agents to your operating cycle to prevent spotting, when the real problem is  
deposited solids on your ware. As the water evaporates off of the ware, the solids will be left behind to form the spotting and  
no amount of drying agent will prevent this. Again, using treated water will undoubtedly reduce the occurrences of this prob-  
lem.  
Third, treated water may not be suitable for use in other areas of your operation. For instance, coffee made with soft water may  
have an acid or bitter flavor. It may only be feasible to install a small treatment unit for the water going into the dishmachine  
itself. Discuss this option with your qualified water treatment specialist.  
Even after the water hardness problems have been solved, there still must be proper training of dishmachine operators in how  
much detergent is to be used per cycle. Talk with your water treatment specialist and detergent vendor and come up with a  
complete training program for operators. Using too much detergent has as detrimental effects as using too little. The proper  
amount of detergent must be used for job. It is important to remember that certain menu items may require extra detergent by  
their nature and personnel need to be made aware of this. Experience in using the dishmachine under a variety of conditions,  
along with good training in the operation of the machine, can go a long way in ensuring your dishmachine operates as effi-  
ciently as possible.  
Certain dishmachine models require that chemicals be provided for proper operation and sanitization. Some models even  
require the installation of third-party chemical feeders to introduce those chemicals to the machine. Jackson does not recom-  
mend or endorse any brand name of chemicals or chemical dispensing equipment. Contact your local chemical distributor for  
questions concerning these subjects.  
Some dishmachines come equipped with integral solid detergent dispensers. These dispensers are designed to accommodate  
detergents in a certain sized container. If you have such a unit, remember to explain this to your chemical distributor upon first  
contacting them.  
As explained before, water temperature is an important factor in ensuring that your dishmachine functions properly. The data  
plate located on each unit details what the minimum temperatures must be for either the incoming water supply, the wash tank  
and the rinse tank, depending on what model of dishmachine you have installed. These temperatures may also be followed by  
temperatures that Jackson recommends to ensure the highest performance from you dishmachine. However, if the minimum  
requirements are not met, the chances are your dishes will not be clean or sanitized. Remember, a dish can look clean, but it  
may not be sanitized. Instruct your dishmachine operators to observe the required temperatures and to report when they fall  
below the minimum allowed. A loss of temperature can indicate a much larger problem such as a failed heater or it could also  
indicate that the hot water heater for your operation is not up to capacity and a larger one may need to be installed.  
There are several factors to consider when installing your dishmachine to ensure that you get the best possible results from it  
and that it operates at peak efficiency for many years. Discuss your concerns with your local chemical distributor and water  
treatment specialist before there is a problem.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
10  
 
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS  
FALSE PANEL INSTALLATION  
Rack rail removed & reposi-  
tioned for a corner operation.  
False Panel  
False panel positioned in unit.  
1. Remove the rack assembly from the unit.  
2. False panel will mount inside the dishmachine.  
3. Position panel in unit on side to be closed.  
4. Hold panel against side of dishmachine and push up.  
5. Panel will clip in at the top, inside unit.  
6. Holes in false panel will line up with rack assembly holes.  
7. Re-install screws for rack assembly which will secure false  
panel to unit.  
Insert this  
side first.  
8. Re-assemble the rack track in an “L” shape for a corner oper-  
ation.  
Bottom of side panel.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
11  
 
SECTION 3:  
PREVENTATIVE MAINTENANCE  
12  
 
SECTION 3: PREVENTATIVE MAINTENANCE  
PREVENTATIVE MAINTENANCE  
The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However,  
this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs  
not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY. Performing main-  
tenance on your dishmachine may void your warranty if it is still in effect, so if you have a question or concern, do not hesitate  
to contact one of the QUALIFIED SERVICE AGENCIES listed in the back of this manual.  
There are many things that operators can do to prevent catastrophic damage to the dishmachine. One of the major causes of  
component failure has to do with prescrapping procedures. A dishmachine is not a garbage disposal; any large pieces of mate-  
rial that are put into the machine shall remain in the machine until they are either broken up (after spreading out on your ware!)  
or physically removed. Strainers are installed to help catch debris, but they do no good if they are clogged. Have operators reg-  
ularly inspect the pan strainers to ensure (1) that they are free of soil and debris and (2) they are laying flat in the tub.  
When cleaning out strainers, do NOT beat them on waste cans. The strainers are made of metal and can be forgiving; but once  
severe damage is done, it is next to impossible for the strainer to work in the way it was designed to. Wipe out strainers with  
a rag and rinse under a faucet if necessary. For stubborn debris, a toothpick should be able to dislodge any obstructions from  
the perforations. Always ensure that strainers are placed back in the machine before operation and that they lay flat in the tub.  
You may wish to learn more about how your water hardness will effect the performance of your machine. Hard water makes  
dishmachines work harder and decreases efficiency.  
Again, it is important to remind operators that trying to perform corrective maintenance on the dishmachine could lead to larg-  
er problems or even cause harm to the operator. If a problem is discovered; secure the dishmachine using proper shut down  
procedures as listed in this manual and contact a QUALIFIED SERVICE AGENCY.  
Some problems, however, may having nothing to do with the machine itself and no amount of preventative maintenance is  
going to help. A common problem has to do with temperatures being too low. Verify that the water temperatures coming to your  
dishmachine match the requirements listed on the machine data plate. There can be a variety of reasons why your water tem-  
perature could be too low and you should discuss it with a QUALIFIED SERVICE AGENCY to determine what can be done.  
By following the operating and cleaning instructions in this manual, you should get the most efficient results from your machine.  
As a reminder, here are some steps to take to ensure that you are using the dishmachine the way it was designed to work:  
1. Ensure that the water temperatures match those listed on the machine data plate.  
2. Ensure that all strainers are in place before operating the machine.  
3. Ensure that all wash and/or rinse arms are secure in the machine before operating.  
4. Ensure that drains are closed/sealed before operating.  
5. Remove as much soil from dishes by hand as possible before loading into racks.  
6. Do not overfill racks.  
7. Ensure that glasses are placed upside down in the rack.  
8. Ensure that all chemicals being injected to machine have been verified as being at the correct concentrations.  
9. Clean out the machine at the end of every workday as per the instructions in the manual.  
10. Always contact a QUALIFIED SERVICE AGENCY whenever a serious problem arises.  
11. Follow all safety procedures, whether listed in this manual or put forth by local, state or national codes/regulations.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
13  
 
SECTION 4:  
TROUBLESHOOTING SECTION  
14  
 
SECTION 4: TROUBLESHOOTING  
COMMON PROBLEMS  
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified  
service technician. Many of the tests require that the unit have power to it and live electrical components be  
exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE.  
Problem: Dishmachine will not fill after the door is close. Power “ON” light is illuminated.  
1. Faulty rinse solenoid valve. Repair or replace valve as required.  
2. Faulty door switch. Verify the wiring of the switch; if correct, replace the switch.  
3. Fouled/faulty high level probe. Clean probe if fouled. If clean, and still not working, replace.  
Problem: Dishmachine will not fill after the door is closed. Power “ON” light is not illuminated.  
1. Service breaker tripped. Reset. If the breaker trips again, contact an electrician to verify the amp draw of the machine.  
2. Machine not connected to power source. Verify that the machine has been properly connected to the power source.  
3. Faulty power source. Verify the wiring of the switch; if correct, replace switch.  
Problem: Dishmachine will not run after the door is closed. Power “ON” light is illuminated and the unit is filling.  
1. Timer is faulty. Check to see that the timer is receiving power. If so, replace the timer assembly.  
2. Wash motor faulty/damaged. Verify that the wash motor is getting power. If so, replace the motor.  
3. Wash motor contactor faulty. Check for continuity; if contacts are open, replace the contactor.  
Problem: Dishmachine runs continuously in the wash cycle.  
1. Machine is in Delime mode. Flip NORMAL/DELIME switch to NORMAL mode.  
2. Timer motor is faulty. Verify that the timer is rotating. If not, check to see that the motor is receiving power. If so, replace  
the motor and/or timer assembly.  
3. Cam timer jammed by obstruction. Remove obstruction.  
Problem: Wash or rinse heater does not work.  
1. Faulty heater element. Check element for continuity; if open, replace the heater.  
2. Faulty heater contactor. Replace the contactor.  
3. Misadjusted/faulty thermostat(s). Verify operation and setting of thermostats, replace if necessary.  
Problem: Dishmachine fill slowly and/or the rinse is weak.  
1. Clogged or obstructed rinse arms. Remove and clean the rinse arms.  
2. Low incoming water pressure. Adjust the water pressure regulator to ensure that there is 205 PSI flow.  
3. Y-strainer is clogged. Clean out the Y-strainer.  
Problem: Rinse water not reaching required temperature.  
1. Faulty rinse heater. Check element for continuity; if open, replace heater.  
2. Misadjusted/faulty thermostat(s). Verify operation and setting of thermostats, replace if necessary.  
3. Rinse thermometer is defective. Replace thermometer.  
Problem: Wash water is not reaching required temperature.  
1. Faulty wash heater. Check element for continuity; if open, relace the heater.  
2. Misadjusted/faulty thermostat(s). Verify operation and setting of thermostats, replace if necessary.  
3. Wash thermometer is defective. Replace thermometer.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
15  
 
SECTION 4: TROUBLESHOOTING  
COMMON PROBLEMS  
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified  
service technician. Many of the tests require that the unit have power to it and live electrical components  
be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE.  
Problem: Doors will not close completely.  
1. Improper spring tension. Adjust spring tension as required by loosening (not removing) spring bolt nuts and adjusting the  
tension. Tighten nuts back when done.  
2. Obstruction in door channel. Remove the obstruction.  
3. Doors are not square with frame. Adjust the frame to accommodate the doors.  
Problem: Water leaks at the wash pump.  
1. Wash pump seal defective. Replace the seal.  
2. Petcock or pump drain (if equipped) not shut/tight. Close or tighten.  
3. Loose hoses (hose clamps) on the wash pump. Tighten the hose clamps.  
Problem: Will not rinse during autocycle.  
1. Defective rinse solenoid. Repair or replace the rinse solenoid as required.  
2. Faulty timer. Replace timer.  
3. No water to the machine. Verify that there is water at 10 PSI connected to the machine.  
Problem: Dishes are not coming clean.  
1. Machine temperatures are not up to the minimum requirements. Verify that incoming water, rinse water, and wash water  
match the required temperatures as listed on the machine data plate.  
2. No detergent/too much detergent. Adjust detergent concentration as required for the amount of water held by the machine.  
3. Solid dispenser canister is empty. Replace the canister.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
16  
 
SECTION 5:  
PARTS SECTION  
17  
 
SECTION 5: PARTS SECTION  
TOP MOUNTED CONTROL BOX ASSEMBLY WITH UNIVERSAL TIMER  
6
27  
8
8
34  
35  
6
19  
8
8
1
28  
36  
7
8
9
11  
8
2
20  
21  
8
37  
12  
38  
40  
23  
8
13  
33  
32  
8
10  
24  
29  
30  
15  
18  
14  
31  
17  
16  
26  
26  
25  
25  
25  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
18  
 
SECTION 5: PARTS SECTION  
TOP MOUNTED CONTROL BOX ASSEMBLY WITH UNIVERSAL TIMER (CONTINUED)  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
5
6
7
8
9
10  
11  
12  
13  
1
1
2
2
1
19  
1
1
6
1
1
1
1
1
1
1
1
1
1
1
6
3
1
3
2
1
1
1
1
1
4
4
1
1
1
1
1
2
1
Control Box Weldment  
Timer Bracket  
Locknut, 6-32 S/S Hex w/Nylon Insert  
Contactor, 4 Pole  
Terminal Block  
Locknut, 10-24 S/S Hex w/Nylon Insert  
Contactor, Wash Motor 208-230, 30Amp  
Switch, 8 Button  
Holder, Keystone  
Timer, Universal  
05700-003-30-14  
05700-003-02-08  
05310-373-03-00  
05945-109-01-69  
05940-011-48-27  
05310-373-01-00  
05945-002-74-20  
05930-001-99-51  
05940-002-21-87  
05945-003-33-09  
05945-111-47-51  
05945-111-89-75  
05945-111-44-43  
05945-111-44-45  
06685-111-68-48  
06685-111-68-49  
05945-111-44-44  
05940-200-76-00  
05700-002-13-22  
06680-200-08-21  
N/A  
05305-011-39-85  
05700-002-50-02  
05975-011-47-81  
05975-200-40-00  
05975-210-05-00  
05975-002-61-43  
09905-100-75-93  
05700-002-23-03  
09905-003-60-88  
05311-273-03-00  
05305-173-12-00  
09905-011-47-35  
09905-011-86-86  
09905-002-78-67  
05700-002-42-03  
05920-002-42-13  
05305-002-25-91  
09905-003-34-09  
Relay, All Voltages  
Relay, (415V, 3PH, 5 Wire Only)  
Light, Green  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
Light, Red  
Temperature Gauge, Wash 96" Lead  
Temperature Gauge, Rinse 48" Lead  
Light, Yellow  
Ground Lug  
Bracket, Liquid Level Control Board  
Liquid Level Control Board  
Tricnut, 6-32  
Screw, 6-32 x 5/8”  
Spacer, Switch Panel Temp  
Plug, 1/2”  
Grommet, 7/8” Split  
Bushing Snap  
Clamp, Hose, .25-.312  
Decal, Warning-Disconnect Power  
Cover, Top Mount Control Box  
Decal, Control Box  
Lockwasher, Int. Tooth #10  
Screw, 10-32 x 3/8” Phillips Truss Head  
Decal, Copper Conductors  
Decal, Ground  
Decal, L1, L2  
Bracket, Fuse Strip  
Fuse Holder, 6 Pole  
Screw, 6-32 x 3/8” W/ Ext. Tooth Washer  
Decal, Dispenser Connection  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
19  
 
SECTION 5: PARTS SECTION  
HOOD ASSEMBLY (BOLTED SINGLE SUPPORT DESIGN)  
3
1
4
2
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
1
2
6
6
6
4
Hood Weldment (Tempstar/Tempstar LT/Tempstar NB)  
Hood Support  
Bolt, 1/4”-20 x 1/2” Long  
Washer, Flat, SS, 1/4”-20 ID  
Locknut, 1/4”-20 with Nylon Insert (Not Shown)  
Block Spacer  
05700-002-29-79  
05700-002-78-99  
05305-274-21-00  
05311-174-01-00  
05310-374-01-00  
05700-002-81-02  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
20  
 
SECTION 5: PARTS SECTION  
CANTILEVER ARM/DOOR ASSEMBLIES  
2
3
1
10, 11, 12  
13  
4
24, 18  
14  
5
23, 18  
6
9
7
8
15, 16  
17, 18  
19, 11, 21  
20  
19, 11, 12  
22  
3d  
3e  
3a  
3c  
3b  
3f  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
21  
 
SECTION 5: PARTS SECTION  
CANTILEVER ARM/DOOR ASSEMBLIES (CONTINUED)  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
3a  
3b  
3c  
3d  
3e  
3f  
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
17A  
18  
19  
20  
21  
22  
23  
23A  
24  
24A  
25  
26*  
27*  
28  
1
2
2
1
1
1
2
1
2
2
2
2
2
4
2
2
4
4
2
2
1
2
1
1
6
2
2
4
2
1
1
1
1
4
2
6
1
Cantilever Arm  
Spring Pin, 1/4" x 1 1/8"  
Yoke Assembly  
Cotter Pin  
Yoke  
Clevis Pin, 5/16” x 1 3/8”  
Nylon Washer  
Bushing  
Locknut, 3/8”-16 S/S Hex Center  
Rod, Spring  
Spring  
Bolt, Cantilever Hanger Eye 3/8"-16  
Washer, 3/8" ID x 7/8" OD S/S  
Nut, 3/8"-16 S/S Hex  
Connector, Cantilever Arm  
Screw, 1/4"-20 x 1 1/2" Long S/S  
Washer, 1/4" S/S  
Locknut, 1/4"-20 S/S Hex with Nylon Insert Low Profile  
Sleeve, Cantilever Arm  
Plug, Cantilever Arm  
05700-031-50-67  
05315-407-06-00  
05700-000-75-77  
05315-207-01-00  
05700-000-75-78  
05315-700-01-00  
05311-369-03-00  
03120-100-03-00  
05310-256-04-00  
05700-002-29-38  
05340-109-02-00  
05306-956-05-00  
05311-176-02-00  
05310-276-01-00  
05700-011-90-99  
05305-274-23-00  
05311-174-01-00  
05310-374-02-00  
05700-000-85-69  
05340-011-35-00  
05930-111-51-68  
05310-272-02-00  
05700-002-30-88  
05700-002-29-85  
05700-111-33-59  
05305-274-02-00  
05700-000-29-40  
05310-374-01-00  
05700-021-33-39  
05700-002-30-89  
05700-002-29-83  
05700-002-30-87  
05700-002-29-86  
05700-002-20-78  
05700-031-88-00  
05700-011-88-01  
09905-003-57-30  
Magnet, Reed Switch  
Locknut, 8-32 S/S Hex with Nylon Insert  
Door, Right Side (Complete Assembly)  
Right Door Weldment with Studs  
Door, Guides  
Screw, 1/4"-20 x 1/2" Long S/S  
Spacer, PB Bolt  
Locknut, 1/4"-20 S/S Hex with Nylon Insert  
Door Connector Bracket  
Door, Front (Complete Assembly) w/ Decal  
Door Only, Front  
Door, Left Side (Complete Assembly)  
Door Only, Left Side  
Door Connecting Plate  
Bracket, Cantilever Arm Support  
Wear Button, 1/2" Dia. UHMW  
Decal, Jackson LOGO (Not Shown)  
Bracket, Cantilever Arm Support  
09515-003-15-64  
Wear Button, 1/2" Dia. UHMW  
05700-011-88-01  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
22  
 
SECTION 5: PARTS SECTION  
TUB ASSEMBLY  
2
3
5
6
7
8
9
12  
10, 11  
13  
14, 11  
15  
34  
37  
36  
1
3
33  
26  
35  
16  
17  
16  
32  
31, 30  
18  
19  
20  
4
24  
21  
22 23  
25  
27, 28  
29  
* Represents an item not shown.  
Nut, 1/4”-20 Serrated Nut  
05310-011-66-49  
Bracket, Motor Support Weldment  
05700-002-68-31  
Pump Support Adjustable Bracket  
05700-002-20-41  
Pump Support Bracket Complete Assembly  
05700-002-00-46  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
23  
 
SECTION 5: PARTS SECTION  
TUB ASSEMBLY (CONTINUED)  
ITEM QTY  
DESCRIPTION  
Tub Weldment  
Rack Assembly  
Bulk Head Plug  
See Page Entitled “Wash Motors”  
Gasket  
Mfg. No.  
1
2
3
4
5
6
7
8
1
1
2
1
1
1
4
1
1
1
8
1
1
1
1
1
1
1
2
1
1
1
1
1
4
4
1
05700-002-12-59  
05700-002-01-00  
04730-609-05-00  
N/A  
05700-111-35-03  
05330-400-05-00  
05305-276-10-00  
05700-031-46-00  
05700-001-22-23  
05700-001-22-24  
05310-374-02-00  
05700-021-50-07  
05700-001-25-69  
05700-002-91-55  
05700-002-91-54  
05700-002-96-48  
05700-001-27-55  
05330-400-05-00  
04730-719-01-37  
05700-011-88-24  
05700-021-34-84  
05700-002-00-46  
04730-011-34-90  
05975-111-01-00  
05310-276-01-00  
05311-276-01-00  
N/A  
O-ring  
Bolt, Hex 3/8”-16 x 1 1/4" Long  
Lower Wash Manifold Weldment  
Suction Strain Weldment  
Suction Strain Bracket  
Locknut, 1/4"-20 with Nylon Insert  
Strainer Weldment  
Wash Overflow Weldment  
Support, Ball Stop Lift  
Ball Stop Lift  
Shim, Overflow Support  
Overflow Support Bracket  
O-Ring  
Clamp, Hose 1 5/16” to 2 1/4”  
Discharge Hose  
9
10  
11  
12  
13  
*
*
*
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Nipple  
Pump Support Bracket Assembly  
Clamp, Hose 5 5/8" to 6"  
Connector, 1/2” 90  
Nut, 3/8"-16 S/S Hex  
Lockwasher 3/8”  
See Page Entitled “Wash Heaters/Rinse Heaters”  
See page 27 to order phase conversion kits for the heater.  
Probe, High Water  
Locknut, 6-32 with Nylon Insert  
Lockwasher, 5/16", S/S, Split  
Nut, Hex, 5/16"-18, S/S  
Locknut, 10-24 with Nylon Insert  
Cover, Wash Heater  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
1
5
4
4
4
1
1
1
1
1
1
1
06680-200-02-68  
05310-373-03-00  
05311-275-01-00  
05310-275-01-00  
05310-373-01-00  
05700-031-47-57  
09905-100-75-93  
09905-011-84-32  
05700-011-81-64  
05330-011-47-79  
05930-510-02-79  
Decal, Warning-Disconnect Power  
Decal, High Limit  
Thermostat Bracket  
Wash Heater Gasket  
Thermostat, Regulating  
Kit, Wash Thermostat Replacement  
(Includes: thermostat, brass fitting, 2 jumper wires & instructions)  
Thermostat, High Limit  
06401-003-18-22  
05930-011-49-43  
05310-924-02-05  
36  
37  
1
1
Fitting, 1/4" Imperial Brass  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
24  
 
SECTION 5: PARTS SECTION  
STEAM TUB ASSEMBLY  
2
3
5
6
7
8
9
12  
10, 11  
13  
14, 11, 15  
24  
26  
1
3
24  
16  
17  
16  
18  
19  
20  
4
21  
22, 23  
25  
27, 28  
29  
* Represents an item not shown.  
Nut, 1/4”-20 Serrated Nut  
05310-011-66-49  
Bracket, Motor Support Weldment  
05700-002-68-31  
Pump Support Adjustable Bracket  
05700-002-20-41  
Pump Support Bracket Complete Assembly  
05700-002-00-46  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
25  
 
SECTION 5: PARTS SECTION  
STEAM TUB ASSEMBLY (CONTINUED)  
ITEM QTY  
DESCRIPTION  
Tub Weldment  
Rack Assembly  
Bulk Head Plug  
See page entitled “Wash Motors”  
Gasket  
Mfg. No.  
1
2
3
4
5
6
7
8
1
1
2
1
1
1
4
1
1
1
8
1
1
1
1
1
1
1
2
1
1
1
1
1
4
4
1
1
1
1
05700-002-09-26  
05700-002-01-00  
04730-609-05-00  
N/A  
05700-111-35-03  
05330-400-05-00  
05305-276-10-00  
05700-031-46-00  
05700-001-22-23  
05700-001-22-24  
05310-374-02-00  
05700-021-50-07  
05700-001-25-69  
05700-002-91-55  
05700-002-91-54  
05700-002-96-48  
05700-001-27-55  
05330-400-05-00  
04730-719-01-37  
05700-011-88-24  
05700-021-34-84  
05700-002-00-46  
04730-011-34-90  
05975-111-01-00  
05310-276-01-00  
05311-276-01-00  
05310-924-02-05  
06680-200-02-68  
05930-510-02-79  
O-ring  
Bolt, Hex 3/8”-16 x 1 1/4" Long  
Lower Wash Manifold Weldment  
Suction Strain Weldment  
Suction Strain Bracket  
Locknut, 1/4"-20 with Nylon Insert  
Strainer Weldment  
Wash Overflow Weldment  
Support, Ball Stop Lift  
Ball Stop Lift  
Shim, Overflow Support  
Overflow Support Bracket  
O-Ring  
Clamp, Hose 1 5/16” to 2 1/4”  
Discharge Hose  
9
10  
11  
12  
13  
*
*
*
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
Nipple  
Pump Support Bracket Assembly  
Clamp, Hose 5 5/8" to 6"  
Connector, 1/2” 90 Deg.  
Nut, 3/8"-16 S/S Hex  
Lockwasher 3/8”  
Fitting, 1/4" Imperial Brass  
Probe, High Water  
Thermostat, Regulating  
Kit, Wash Thermostat Replacement  
(Includes: thermostat, brass fitting, 2 jumper wires & instructions)  
Cover, Wash Heater  
Decal, Warning-Disconnect Power  
Locknut, 10-24 with Nylon Insert  
Locknut, 6-32 with Nylon Insert  
06401-003-18-67  
05700-031-47-57  
09905-100-75-93  
05310-373-01-00  
05310-373-03-00  
27  
28  
29  
30  
1
1
2
3
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
26  
 
SECTION 5: PARTS SECTION  
FRAME ASSEMBLY  
Front Panel  
05700-002-36-65  
Locknut, 1/4”-20 S/S Hex with Nylon Insert  
05310-374-02-00  
Bolt, 1/4”-20 x 1/2”  
05305-274-02-00  
Frame Weldment  
05700-031-48-01  
Bullet Foot  
05340-108-01-03  
Flanged Bullet Foot  
05340-002-34-86  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
27  
 
SECTION 5: PARTS SECTION  
RINSE TANK ASSEMBLY  
See page 27 to order phase  
conversion kits for the heater.  
2, 3  
5
4
6
10  
11  
1
7, 8  
See page entitled  
“WASH HEATERS/RINSE  
HEATERS”.  
9
12  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
9
1
2
2
1
1
6
4
4
1
1
Booster Tank Weldment  
Locknut, 10-24 with Nylon Insert  
Washer, #10 S/S Flat  
Decal, Warning - Disconnect Power  
Booster Tank Cover Weldment  
Nut, Hex, 5/16"-18  
Locknut, 1/4"-20 with Nylon Insert  
Washer, 1/4" ID, S/S, Flat  
Thermostat, Rinse  
05700-001-22-02  
05310-373-01-00  
05311-173-01-00  
09905-100-75-93  
05700-001-29-30  
05310-275-01-00  
05310-374-01-00  
05311-174-01-00  
05930-510-03-79  
Kit, Rinse Thermostat Replacement  
(Includes: thermostat, brass fitting, 2 jumper wires & instructions)  
Washer, 5/16” I.D.  
Gasket, Rinse Heater  
06401-011-66-55  
05311-175-01-00  
05330-200-02-70  
05310-924-02-05  
10  
11  
12  
6
1
1
Fitting, 1/4" Imperial Brass  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
28  
 
SECTION 5: PARTS SECTION  
RINSE TANK AND ROUND FLANGE HEATER ASSEMBLY  
See page 27 to order phase  
conversion kits for the heater.  
2, 3  
10, 13  
5
4
6
11  
1
7, 8  
See page entitled  
“RINSE HEATERS -  
ROUND FLANGED  
HEATERS”.  
9
12  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
9
1
2
2
1
1
8
4
4
1
1
Booster Tank Weldment  
Locknut, 1/4-20 with Nylon Insert  
Washer, 1/4” S/S Flat  
Decal, Warning - Disconnect Power  
Booster Tank Cover Weldment  
Nut, Hex, 1/4-20"-18  
Locknut, 1/4"-20 with Nylon Insert  
Washer, 1/4" ID, S/S, Flat  
Thermostat, Rinse  
05700-003-58-41  
05310-374-01-00  
05311-174-01-00  
09905-100-75-93  
05700-001-29-30  
05310-274-01-00  
05310-374-01-00  
05311-174-01-00  
05930-510-03-79  
Kit, Rinse Thermostat Replacement  
(Includes: thermostat, brass fitting, 2 jumper wires & instructions)  
Washer, 1/4” I.D.  
Gasket, Rinse Heater  
Fitting, 1/4" Imperial Brass  
Washer, 1/4” Split Lock  
06401-011-66-55  
05311-174-01-00  
05330-200-02-70  
05310-924-02-05  
05311-274-01-00  
10  
11  
12  
13  
8
1
1
8
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
29  
 
SECTION 5: PARTS SECTION  
COIL ASSEMBLY  
Complete Steam Coil Assembly  
05700-002-08-62  
Stand C, Steam Coil Support  
05700-002-08-52  
Steam Coil Weldment  
05700-021-41-38  
Stand D, Steam Coil Support  
05700-002-08-53  
Stand B, Steam Coil Support  
05700-002-08-51  
Stand A, Steam Coil Support  
05700-002-08-50  
Gasket, Steam Coil  
4 per assembly  
05700-001-17-86  
Washer, Steam Coil  
2 per assembly  
05700-001-17-87  
Adapter, Steam Coil Nut  
2 per assembly  
05310-011-17-85  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
30  
 
SECTION 5: PARTS SECTION  
INCOMING STEAM PLUMBING ASSEMBLIES  
To order this complete assembly, use part number:  
05700-002-01-55  
Union, 3/4’’ NPT, Black Iron  
04730-912-01-01  
Bushing, Reducing, 3/4’’ to 1/2’’  
04730-911-02-34  
Steam Trap, 3/4” NPT F&T  
06680-500-02-77  
Elbow, 3/4” 90° Street  
04730-011-87-37  
Nipple, Close, 3/4’’ NPT, Black Iron  
04730-907-01-00  
To order this complete assembly, use part number:  
05700-002-01-60  
Bushing, Reducing, 3/4’’ to 1/2’’  
04730-911-02-34  
Elbow, 3/4” 90° Street  
04730-011-87-37  
Union, 3/4’’ NPT, Black Iron  
2 per assembly  
04730-912-01-01  
3/4” NPT Black Iron Pipe  
05700-002-20-83  
Solenoid Valve, Steam Plumbing, 220V  
04820-002-01-32  
Bracket, Steam Plumbing Support  
05700-002-20-83  
Y-Strainer, 3/4” NPT Black Iron  
04730-217-01-32  
Elbow, 903/4” NPT Black Iron  
04730-011-87-37  
Gate Valve, 3/4” NPT  
04820-100-19-00  
Nipple, Close, 3/4’’ NPT, Black Iron  
4 per Assembly  
04730-907-01-00  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
31  
 
SECTION 5: PARTS SECTION  
WASH MOTORS  
The Tempstar models covered in this manual come supplied with various wash motor assemblies (a wash motor assembly  
includes the wash motor and the pump end), depending on the characteristics of the machine. To ensure that you order the  
correct wash motor assembly for the model you are servicing, please refer to the following table:  
Model  
Volts  
Hz  
Phase  
Wash Motor Assembly  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
Tempstar/Tempstar NB  
208  
208  
208  
208  
230  
230  
230  
230  
380  
415  
440  
460  
50  
50  
60  
60  
50  
50  
60  
60  
50  
50  
50  
60  
1
3
1
3
1
3
1
3
3
3
3
3
06105-002-19-87  
06105-002-19-87  
06105-002-69-78  
06105-002-69-78  
06105-002-19-87  
06105-002-19-87  
06105-002-69-78  
06105-002-69-78  
06105-002-41-24  
06105-002-41-24  
06105-002-41-24  
06105-121-64-21  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
208  
208  
208  
208  
230  
230  
230  
230  
380  
415  
440  
460  
50  
50  
60  
60  
50  
50  
60  
60  
50  
50  
50  
60  
1
3
1
3
1
3
1
3
3
3
3
3
06105-002-19-87  
06105-002-19-87  
06105-002-69-78  
06105-002-69-78  
06105-002-19-87  
06105-002-19-87  
06105-002-69-78  
06105-002-69-78  
06105-002-41-24  
06105-002-41-24  
06105-002-41-24  
06105-121-64-21  
Tempstar S  
Tempstar S  
Tempstar S  
Tempstar S  
208  
208  
230  
230  
60  
60  
60  
60  
1
3
1
3
06105-002-69-78  
06105-002-69-78  
06105-002-69-78  
06105-002-69-78  
Important note: When servicing a wash motor, it is important to refer to the wiring schematic found on the motor, to ensure  
that the motor is wired correctly. Different manufacturers of motors may not use the same wire color codes and therefore, your  
new motor, which may have been built by someone different than who built your original motor, may not connect using the same  
wires. Always refer to the wiring diagrams on the motor you are installing. If the motor you are installing has had the schemat-  
ic removed, contact Jackson MSC immediately for technical support.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
32  
 
SECTION 5: PARTS SECTION  
MOTOR & PUMP ASSEMBLY  
Complete Pump & Motor Assembly, 60HZ  
Complete Pump & Motor Assembly, 50HZ  
06105-002-19-87  
06105-002-69-78  
Motor Only, 60HZ  
06105-002-79-61  
Pump Only Assembly, 60HZ  
Pump Only Assembly, 50HZ  
(Area indicated within box, Casing is included) (Area indicated within box, Casing is included)  
Motor Only, 50HZ  
06105-002-85-36  
05700-002-79-51  
05700-002-85-38  
Pump Casing (Not shown), 50HZ  
05700-002-41-50  
Shim Kit, 60HZ  
05700-002-82-58  
Case Capscrew, 60HZ  
05305-002-81-88  
Pump Casing 60HZ  
05700-002-85-01  
Mechanical Seal, 60HZ  
05330-002-34-22  
Seal, 50HZ  
05330-002-06-21  
Case O-Ring, 60HZ  
05330-002-81-83  
Seal Plate, 60HZ  
05700-002-81-87  
Other parts not shown.  
Drain Plug, 60HZ  
04730-002-81-89  
Gasket, 50HZ  
05330-002-41-48  
Impeller Assembly, 60HZ  
05700-002-81-86  
Bracket, 50HZ  
05700-002-06-22  
Impeller Assembly, 50HZ  
05700-002-41-49  
Shaft Adapter, 50HZ  
05700-011-95-49  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
33  
 
SECTION 5: PARTS SECTION  
WASH HEATERS/RINSE HEATERS  
The Tempstar models covered in this manual come supplied with various heaters, depending on the characteristics of the machine.  
To ensure that you order the correct heater for the model you are servicing, please refer to the following table:  
Model  
Volts  
Hz  
Phase  
Wash Heater  
Rinse Heater (12 KW)  
Rinse Heater (14 KW)  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
208  
208  
208  
208  
230  
230  
230  
230  
380  
415  
440  
460  
50  
50  
60  
60  
50  
50  
60  
60  
50  
50  
50  
60  
1
3
1
3
1
3
1
3
3
3
3
3
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-002-44-31  
04540-002-43-09  
04540-121-65-99  
04540-121-65-99  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-121-47-40  
04540-002-44-32  
04540-002-43-10  
04540-100-01-15  
04540-100-01-15  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-121-63-38  
04540-002-77-24  
04540-121-63-39  
04540-121-63-39  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
Tempstar LT  
208  
208  
208  
208  
230  
230  
230  
230  
380  
440  
460  
50  
50  
60  
60  
50  
50  
60  
60  
50  
50  
60  
1
3
1
3
1
3
1
3
3
3
3
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-002-44-31  
04540-121-65-99  
04540-121-65-99  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
Tempstar NB  
208  
208  
208  
208  
230  
230  
230  
230  
380  
415  
440  
460  
50  
50  
60  
60  
50  
50  
60  
60  
50  
50  
50  
60  
1
3
1
3
1
3
1
3
3
3
3
3
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-121-47-39  
04540-002-44-31  
04540-002-43-09  
04540-121-65-99  
04540-121-65-99  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 BA  
Issued: 10-08-2008 Revised: N/A  
34  
 
SECTION 5: PARTS SECTION  
RINSE HEATERS - ROUND FLANGED HEATER  
The Tempstar models covered in this manual come supplied with various heaters, depending on the characteristics of the machine.  
To ensure that you order the correct heater for the model you are servicing, please refer to the following table:  
Model  
Volts  
Hz  
Phase  
Rinse Heater (12 KW)  
Rinse Heater (14 KW)  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
Tempstar  
208  
208  
208  
208  
230  
230  
230  
230  
50  
50  
60  
60  
50  
50  
60  
60  
1
3
1
3
1
3
1
3
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-27  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
04540-003-58-28  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
35  
 
SECTION 5: PARTS SECTION  
TEMPSTAR INCOMING PLUMBING/OUTLET PLUMBING ASSEMBLY  
TEMPSTAR  
TEMPSTAR INCOMING PLUMBING  
(Complete Assembly) 05700-003-60-74  
OUTLET PLUMBING  
(Complete assembly)  
05700-003-60-75  
11  
3
18  
8
2
14  
12  
17  
12  
5
9
4
17  
8
9
1
10  
Tube Length Chart  
15  
Item # Length (Inches)  
10  
13  
15  
17  
18  
19  
1/2” x 37" Long  
1/2” x 3 1/2" Long  
1/2" x 30 3/4" Long  
1/2" x 3" Long  
1/2” x 2 1/2” Long  
1/2” X 2 1/8” Long  
12  
16  
11  
19  
13  
8
12  
19  
12  
7
17  
12  
7
11  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
36  
 
SECTION 5: PARTS SECTION  
TEMPSTAR INCOMING PLUMBING/OUTLET PLUMBING ASSEMBLY/WPRK KIT OPTION  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
1
1
1
1
1
2
2
3
2
1
3
6
1
1
1
1
3
1
2
Water Pressure Regulator, 1/2" NPT  
Valve, Ball, 1/4" NPT  
05700-100-04-07  
04810-011-72-67  
06685-111-88-34  
04730-411-25-01  
04730-100-09-18  
05700-003-60-90  
04730-002-56-27  
04730-406-01-01  
04730-011-59-53  
See Chart  
04730-406-01-01  
04730-401-03-01  
See Chart  
04820-003-06-13  
See Chart  
Gauge, Pressure, 0-100 PSI  
Tee, Brass, 1/2" NPT x 1/2" x 1/4"  
Valve, Solenoid, 1/2" NPT  
Bracket, Booster Plumbing 1/2” (Not Shown)  
Bushing, HEX 3/4 MNPT-1/2 FNPT Brass  
Union, 1/2”  
Adapter, 1/2” MNPT x CU Male  
Tube, Copper  
Elbow, 1/2" CU x CU, 90  
Adapter, 1/2”  
Tube, Copper  
Vacuum Breaker, 1/2" NPT  
Tube, Copper  
Elbow, 1/2" NPT, 90, Brass  
Tube, Copper  
Tube, Copper  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
04730-011-42-96  
See Chart  
See Chart  
Tube, Copper  
See Shart  
When servicing plumbing components, take care not to damage the threads of each individual item. Damaged threads can  
cause leaks and loss of pressure, which could adversely effect the performance of the Tempstar dishmachine. It is strongly rec-  
ommended that teflon thread tape, used in conservative amounts, be applied to threads when joining components together. It  
is not advised to use thread sealing compounds, sometimes referred to as “pipe dope”. Compounds can be ejected from the  
threads during the tightening process and become lodged in key components, thereby rendering them useless. Some of the  
components include the solenoid valve and the pressure gauge isolation ball valve.  
WPRK KIT OPTION  
Water Arrestor, 1/2”  
06685-100-05-00  
Tee, 1/2” x 1/2” x 1/2”  
04730-211-27-00  
Nipple, 1/2” NPT, Close, Brass  
04730-207-15-00  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
37  
 
SECTION 5: PARTS SECTION  
TEMPSTAR LT & TEMPSTAR NB INCOMING PLUMBING ASSEMBLY  
(Complete Assembly) 05700-003-60-73  
8
2
11  
6
10  
4
9
5
7
2
1
2
3
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
1
3
1
1
1
1
1
1
1
1
1
Tee, Brass, 1/2" x 1/2" x 1/4" NPT  
Adapter, 1/2” MNPT x Cu Male  
Water Pressure Regulator, 1/2" NPT  
Valve, Ball, Bronze, 1/4" NPT  
Adapter, 1/2” Male/Cu to MSPS  
Pressure Gauge, 0-100 PSI  
Valve, Solenoid, 1/2" NPT 208-240V  
Vacuum Breaker, 1/2" NPT  
Tube, Copper 1/2” x 5.75  
04730-411-25-01  
04730-011-59-53  
04820-100-04-07  
04810-011-72-67  
04730-401-03-01  
06685-111-59-66  
04810-100-09-18  
04820-003-06-13  
05700-002-91-03  
04730-412-05-01  
04730-406-32-01  
9
10  
11  
Union, 1/2”  
Elbow, 1/2” 90º Cu to MSPS  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
38  
 
SECTION 5: PARTS SECTION  
1/2” SOLENOID VALVE & 1/2” NPT VACUUM BREAKER REPAIR PARTS KITS  
Screw  
Cap Screw  
Data Plate  
Coil & Housing  
Data Plate  
Cap  
Valve Bonnet  
Spring & Plunger Kit  
06401-003-07-40  
Cap Retainer  
O-Ring  
Plunger  
Body  
O-Ring & Diaphragm  
06401-003-07-42  
Diaphragm  
Retainer  
Components of Repair Kit  
06401-003-06-23  
Screen  
Retainer  
Mesh Screen  
Valve Body  
Complete Vacuum Breaker Assembly, 1/2” NPT  
04820-003-06-13  
Complete 110 Volt Solenoid Valve Assembly, 1/2”  
04810-100-12-18  
Coil & Housing only  
06401-003-07-43  
Complete 240 Volt Solenoid Valve Assembly, 1/2”  
04810-100-09-18  
Coil & Housing only  
06401-003-07-44  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
39  
 
SECTION 5: PARTS SECTION  
WASH & RINSE ARM/MANIFOLD ASSEMBLIES  
10  
18  
11  
13  
20  
10  
12  
15  
14  
Rinse Injector Weldment  
1 per machine  
05700-002-56-75  
10  
Plug, 1/8” NPT, Brass  
3 per Rinse Injector  
04730-209-07-37  
10  
DETAIL “A”  
FINAL RINSE ARMS & MANIFOLD  
Rinse Injector Gasket  
2 per machine  
05330-111-42-81  
2, 3, 4  
5
1
1
17  
7
9, 17  
6, 10  
7
9
9, 17  
17  
5
16, 8  
16  
2, 3, 19  
DETAIL “B”  
WASH ARMS & MANIFOLD  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
40  
 
SECTION 5: PARTS SECTION  
WASH & RINSE ARM/MANIFOLD ASSEMBLIES (CONTINUED)  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
1
4
4
2
2
1
1
2
2
5
2
4
2
2
4
1
2
1
1
1
1
15  
20  
1
2
2
Upper Manifold  
Nut, 3/8"-16 S/S Hex  
Lockwasher,3/8  
Bolt, Hex 3/8”-16 x 7/8" Long  
O Ring  
Positioning Bracket, Manifold Tube  
Tube, Wash Manifold  
Gasket, Manifold  
05700-031-34-82  
05310-276-01-00  
05311-276-01-00  
05306-011-36-95  
05330-111-35-15  
05700-011-34-63  
05700-131-15-07  
05700-111-35-03  
05700-021-35-93  
05310-374-01-00  
05340-112-01-11  
05330-011-42-10  
05700-021-33-84  
05700-003-58-94  
04730-609-04-00  
05700-031-46-00  
05700-021-35-97  
05700-011-35-94  
05700-011-35-96  
05700-011-35-95  
05340-011-37-81  
03120-100-02-00  
03120-011-37-82  
05700-021-47-61  
05305-276-10-00  
03120-002-72-24  
9
Wash Arm  
10  
11  
12  
13  
14  
15  
16  
17  
17a  
17b  
17c  
17d  
17e  
17f  
18  
19  
20  
Locknut, 1/4"-20 S/S Hex with Nylon Insert  
Clip, Retaining, Rinse Head Bushing  
Rinse Arm Washer  
Bushing, Rinse Head  
Rinse Arm  
Plug, Rinse Arm  
Lower Wash Manifold  
Bearing Assembly  
Hub Nut  
Hub Bushing  
Hub Spindle  
Ring, Retainer  
3/16" Stainless Steel Ball  
1/8" Stainless Steel Ball  
Rinse Manifold Assembly  
Bolt, Hex 3/8”-16 x 1 1/4" Long  
Bearing, Rinse Head  
9
17c  
EXPLODED VIEW OF  
ITEM 17  
17a  
17b  
17f  
17d  
17e  
1 or 16  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
41  
 
SECTION 5: PARTS SECTION  
SAFETY DOOR INTERLOCK (SDI) /EXHAUST FAN CONTROL/TRANSFORMER MOUNTING BOX  
Safety Door Interlock Box Cover  
Safety Door Interlock Box Bottom  
05700-001-21-27  
05700-001-21-26  
Other Safety Door Interlock (SDI) components (not shown):  
DESCRIPTION  
Mfg. No.  
Pipe Clamp (found on the side of the machine)  
Solenoid, Electrical Interlock Option  
Relay  
05700-000-35-05  
04810-100-61-33  
05945-111-47-51  
Exhaust Fan  
Control  
2” Din Rail  
05700-002-36-09  
Transformer Mounting Bracket  
05700-031-62-82  
Exhaust Fan  
Control  
Delay Timer  
05945-011-65-44  
Transformer Mounting Box  
05700-002-10-01  
415/440/460V  
Transformer  
05950-111-65-93  
Transformer Mounting Box Top  
(not shown)  
2 Amp Circuit Breaker  
05925-111-64-18  
05700-000-78-53  
380V Transformer  
05950-111-64-17  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
42  
 
SECTION 5: PARTS SECTION  
FALSE PANEL INSTALLATION  
Left & Front False Panel  
Weldment  
Rack rail removed & reposi-  
tioned for a corner operation.  
05700-002-75-52  
Right False Panel Weldment  
(Use with Overflow Tube Lifter)  
05700-002-98-85  
Left & Front False Panel Kit  
05700-002-75-59  
Right False Panel Kit  
(Use with Overflow Tube Lifter)  
05700-002-98-86  
False panel positioned in unit.  
1. Loosen the rack assembly from the unit.  
2. False panel will mount to the rack; inside the dishmachine.  
3. Position panel in unit on side to be closed.  
4. Hold panel against side of dishmachine and push up.  
5. Panel will clip inside the unit under the edge of the hood.  
6. Holes in false panel will line up with rack assembly holes.  
7. Re-install screws for rack assembly which will secure false panel  
to unit.  
Insert this  
side first.  
8. Re-assemble the rack track in an “L” shape for a corner opera-  
tion.  
Bottom of side panel.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
43  
 
SECTION 5: PARTS SECTION  
GO*BOX COMPONENTS  
A GO*BOX is a kit of the most needed parts for a particular model or model family to successfully effect a repair in the first call  
90% or more of the time.  
The following components may be ordered together using the following Mfg. No.: 06401-003-62-04  
ITEM QTY  
DESCRIPTION  
Mfg. No.  
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
1
6
2
1
1
1
1
2
1
1
1
4
1
1
Contactor, Rinse/Wash Heater  
Contactor, Wash Motor  
05945-109-01-69  
05945-002-74-20  
06685-111-88-34  
06685-111-68-49  
06685-111-68-48  
06401-140-00-33  
06401-140-00-32  
05930-011-49-43  
06680-200-08-21  
06680-200-02-68  
05930-111-51-68  
05700-111-33-59  
05330-111-35-15  
05945-111-47-51  
05330-002-34-22  
05330-002-81-83  
05930-111-51-69  
05340-112-01-11  
05700-021-35-97  
05930-002-29-13  
05945-003-33-09  
05330-011-42-10  
04820-003-06-13  
04810-100-09-18  
Gauge, Pressure, 0-100 PSI  
Thermometer, 96" Capillary  
Thermometer, 48" Capillary  
Thermostat, Rinse Operating  
Thermostat, Wash Operating  
Thermostat, Hi-Limit  
Liquid Level Control  
Probe, water level sensing  
Magnet,Door  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Glide, Door Edge  
O-Ring Wash Manifold  
Relay,Control 240V 50/60Hz  
Seal, Mechanical Pump (S/S Pumps)  
O-Ring, Wash Pump Gasket  
Switch, Door, Magnetic Reed  
Snap Ring, Retaining, Rinse Arm  
Bearing Assembly, Wash Arm  
Switch, Power Push Button  
Timer, Universal  
Washer, Rinse Arm Nylatron  
Vacuum Breaker 1/2" Brass  
Valve, Solenoid, 1/2", 208-220V  
*
1
Pump & Motor Assembly, S/S  
06105-002-69-78  
Special pricing available when purchased with above GO*BOX. Call for details.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
44  
 
SECTION 5: PARTS SECTION  
DRAIN QUENCH ASSEMBLY  
Elbow, 1-1/2” 90Street  
04730-206-32-00  
Drain Quench  
Assembly  
06401-002-59-52  
Nipple, 1-1/2” NPT  
04730-207-40-00  
Modified Compression  
Fitting  
Lid, Drain Quench  
05700-002-67-16  
05700-001-16-52  
Thermostat  
05930-003-13-65  
Solenoid Valve  
04810-100-09-18  
Reducer, 1-1/2” x 1/4”  
04730-002-55-76  
To Dishmachine Drain  
To Cold Water Supply  
Tee, 1-1/2” x 1-1/2” x 1-1/2”  
04730-011-69-93  
Box, Drain Quench  
05700-002-69-96  
Valve, Check, 1/2”  
(Not Shown)  
Reducer, 1-1/2” to 1/2”  
04730-002-55-75  
Nipple, Close, 1/2” NPT  
(Not Shown)  
04820-002-55-77  
04730-207-15-00  
From the existing drain, attach the two additional Tees using the 1-1/2” NPT Close Nipples. Tighten the Reducers into the Tees  
as shown above. Attach the Modified Compression Fitting into the 1-1/2” to 1/4” Reducer. Position the bulb of the thermostat  
so that it rests approximately 1/4” from the bottom of the Tee. Tighten the Modified Compression Fitting as required. Attach to  
the incoming cold water line. Use pipe dope or thread tape as required to prevent any leaks.  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
45  
 
SECTION 6A:  
ELECTRICAL SCHEMATICS  
FOR TOP MOUNT UNITS  
46  
 
SECTION 6: ELECTRICAL SCHEMATICS  
TEMPSTAR (TOP MOUNT W/ CYCLE SWITCHES) 208-230 VOLT - 50/60 HERTZ - SINGLE & THREE PHASE  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
47  
 
SECTION 6: ELECTRICAL SCHEMATICS  
TEMPSTAR (TOP MOUNT W/ CYCLE SWITCHES) 460 VOLT - 60 HERTZ -THREE PHASE  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
48  
 
SECTION 6: ELECTRICAL SCHEMATICS  
TEMPSTAR LT & NB (TOP MOUNT W/ CYCLE SWITCHES) 208-230 VOLT - 50/60 HERTZ - SINGLE & THREE PHASE  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
49  
 
SECTION 6: ELECTRICAL SCHEMATICS  
TEMPSTAR LT & NB (TOP MOUNT W/ CYCLE SWITCHES) 460 VOLT - 50/60 HERTZ - SINGLE & THREE PHASE  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
50  
 
SECTION 6: ELECTRICAL SCHEMATICS  
TEMPSTAR S (TOP MOUNT UNIVERSAL TIMER) 208-230 VOLT - 50/60 HERTZ - SINGLE & THREE PHASE  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
51  
 
SECTION 6C:  
ELECTRICAL SCHEMATICS  
FOR OPTIONS  
52  
 
SECTION 6: ELECTRICAL SCHEMATICS  
SDI OPTION  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
53  
 
SECTION 6: ELECTRICAL SCHEMATICS  
EXHAUST FAN HOOKUP/DRAIN QUENCH OPTIONS  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
54  
 
SECTION 7:  
JACKSON MAINTENANCE &  
REPAIR CENTERS  
55  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
ALABAMA TO FLORIDA  
ALABAMA  
CALIFORNIA  
P & D APPLIANCE  
4220-C ROSEVILLE ROAD  
NORTH HIGHLANDS, CA  
95660  
GCS SERVICE INC.  
PHILADELPHIA, PA  
(215)925-6217  
JONES-McLEOD APPLIANCE  
SVC  
BARKERS FOOD MACHINERY  
SERVICES  
800-441-9115  
1616 7TH AVE. NORTH  
BIRMINGHAM, AL 35203  
(205) 251-0159  
800-821-1150  
FAX: (205) 322-1440  
[email protected]  
5367 SECOND STREET  
IRWINDALE, CA 91706  
(626) 960-9390  
800-258-6999  
FAX: (626) 337-4541  
[email protected]  
(916) 974-2772  
800-824-7219  
FAX:(916) 974-2774  
FAX: (215) 925-6208  
ELMER SCHULTZ SERVICE  
36 BELMONT AVE.  
WILLMINGTON, DE 19804  
(302) 655-8900  
COMMERCIAL APPLIANCE  
SERVICE, INC.  
281 LATHROP WAY, #100  
SACRAMENTO, CA 95815  
(916) 567-0203  
(800) 464-2222  
(916) 567-0324 FAX  
800-225-0599  
FAX: (302) 656-3673  
[email protected]  
JONES-McLEOD APPLIANCE  
SVC  
854 LAKESIDE DRIVE  
MOBILE, AL 36693  
(251) 666-7278  
GCS SERVICE INC.  
LOS ANGELES, CA  
(213) 683-2090  
800-327-1433  
FAX: (213) 683-2099  
EMR SERVICE DIVISION  
106 WILLIAMSPORT CIRCLE  
SALISBURY, MD 21804  
(410) 543-8197  
800-237-9859  
FAX: (251) 661-0223  
COLORADO  
GCS SERVICE INC.  
SANTA ANA, CA  
(714) 542-1798  
GCS SERVICE INC.  
SHERIDAN, CO  
(303) 371-9054  
FAX: (410) 548-4038  
ALASKA  
800-540-0719  
FLORIDA  
RESTAURANT APPLIANCE  
SERVICE  
7219 ROOSEVELT WAY NE  
SEATTLE, WA 98115  
(206) 524-8200  
800-433-9390  
FAX: (206) 525-2890  
[email protected]  
FAX: (714) 542-4787  
800-972-5314  
FAX: (303) 371-4754  
COMMERCIAL APPLIANCE  
SERVICE  
8416 LAUREL FAIR CIRCLE  
BLDG 6, SUITE 114  
TAMPA, FL 33610  
(813) 663-0313  
GCS SERVICE INC.  
S. SAN FRANCISCO, CA  
(650) 635-0720  
800-969-4427  
FAX: (650) 871-4019  
HAWKINS COMMERCIAL  
APPLIANCE SERVICE  
3000 S. WYANDOT ST.  
ENGLEWOOD, CO 80110  
(303) 781-5548  
800-282-4718  
COMMERCIAL APPLIANCE  
SERVICE, INC.  
6507 PACIFIC AVENUE, SUITE  
102  
STOCKTON, CA 95207  
(916) 567-0203  
(800) 464-2222  
(800) 624-2117  
FAX: (303) 761-5561  
[email protected]  
FAX: (813) 663-0212  
commercialappliance@world-  
net.att.net  
ARIZONA  
AUTHORIZED COMMERCIAL  
FOOD EQMT. SVC  
4832 SOUTH 35TH STREET  
PHOENIX, AZ 85040  
(602) 234-2443  
METRO APPLIANCE SERVICE  
1640 S BROADWAY  
DENVER, CO 80210  
(303) 778-1126  
GCS SERVICE INC  
MIAMI, FL  
(305) 621-6666  
800-766-8966  
(916) 567-0266 FAX  
800-824-8875  
800-525-3532  
FAX: (305) 621-6656  
FAX: (602) 232-5862  
[email protected]  
GCS SERVICE INC.  
SAN DIEGO, CA  
(858) 549-8411  
FAX: (303) 778-0268  
[email protected]  
GCS SERVICE INC  
ORLANDO, FL  
GCS SERVICE INC.  
PHOENIX, AZ  
800-422-7278  
FAX: (858) 549-2323  
CONNECTICUT  
(407) 841-2551  
800-338-7322  
(602) 474-4510  
800-510-3497  
FAX: (602) 470-4511  
GCS SERVICE INC.  
HARTFORD, CT  
(860) 549-5575  
800-423-1562  
FAX: (860) 527-6355  
FAX: (407) 423-8425  
INDUSTRIAL ELECTRIC SVC.  
5662 ENGINEER DRIVE  
HUNTINGTON BEACH, CA  
92649  
NASS PARTS AND SERVICE,  
INC.  
1144 BELVILLE ROAD, UNIT  
359  
ARKANSAS  
(714) 379-7100  
BROMLEY PARTS & SVC  
10TH AND RINGO  
(800-457-3783  
FAX: (714) 379-7109  
SUPERIOR KITCHEN SER-  
VICE INC.  
DAYTONA BEACH, FL 32114  
(386) 226-2642  
P.O. BOX 1688  
LITTLE ROCK, AR 72202  
(501) 374-0281  
22 THOMPSON ROAD  
WINDSOR, CT 06088  
(888) 590-1899  
(800) 432-2795  
(386) 736-7695 FAX  
P & D APPLIANCE SVC  
100 SOUTH LINDEN AVE.  
S. SAN FRANCISCO, CA 94080  
(650) 635-1900  
800-424-1414  
FAX: (650) 635-1919  
[email protected]  
800-482-9269  
(888) 590-1996 FAX  
GCS SERVICE INC  
TAMPA, FL  
(813) 626-6044  
800-282-3008  
FAX: (501) 374-8352  
[email protected]  
[email protected]  
DELAWARE  
FOOD SERVICE EQMT.  
2101 PARKWAY SOUTH  
BROOMALL, PA 19008  
(610) 356-6900  
FAX: (610) 356-2038  
[email protected]  
FAX: (813) 621-1174  
GCS SERVICE,INC.  
3717 CHERRY ROAD  
MEMPHIS, TN 38118  
(901) 366-4587  
800-262-9155  
FAX: (901) 366-4588  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
56  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
FLORIDA TO MARYLAND  
JONES-McLEOD APPLIANCE  
SVC  
854 LAKESIDE DRIVE  
MOBILE, AL 36693  
(251) 666-7278  
800-237-9859  
FAX: (251) 661-0223  
[email protected]  
HAWAII  
INDIANA  
CERTIFIED SERVICE CENTER  
1051 GOODWIN DRIVE  
LEXINGTON, KY 40505  
(606) 254-8854  
800-432-9269  
FAX: (606) 231-7781  
[email protected]  
FOOD EQMT. PARTS &  
SERVICE CO.  
300 PUUHALE RD.  
HONOLULU, HI 96819  
(808) 847-4871  
GCS SERVICE INC.  
INDIANAPOLIS, IN  
(317) 545-9655  
800-727-8710  
FAX: (317) 549-6286  
FAX: (808) 842-1560  
[email protected]  
B622 LA PAS TRAIL  
INDIANAPOLIS, IN 46268  
(317) 290-8060  
(800) 410-9794  
(317) 290-8085 FAX  
NASS PARTS AND SERVICE,  
INC.  
1108 SOUTH WOODS AVENUE  
ORLANDO, FL 32805  
(407) 425-2681  
GCS SERVICE INC.  
LOUISVILLE, KY  
(502) 367-1788  
800-752-6160  
FAX: (502) 367-0400  
IDAHO  
RESTAURANT APPLIANCE  
SVC.  
(800) 432-2795  
(407) 425-3463 FAX  
7219 ROOSEVELT WAY NE  
SEATTLE, WA 98115  
(206) 524-8200  
IOWA  
GOODWIN TUCKER GROUP  
GCS SERVICE INC.  
LEXINGTON, KY  
(606) 255-0746  
800-432-9260  
FAX: (606) 255-0748  
NASS PARTS AND SERVICE,  
INC.  
1376 HEIDE AVENUE  
PALM BAY, FL 32907  
(321) 952-2012  
800-433-9390  
FAX: (206) 525-2890  
[email protected]  
2900 DELAWARE AVENUE  
DES MOINES, IA 50317  
(515) 262-9308  
800-372-6066  
FAX: (515) 262-2936  
[email protected]  
RON'S SERVICE  
LOUISIANA  
(800) 432-2795  
(321) 953-0266 FAX  
703 E 44TH STREET STE 10  
GARDEN CITY, ID 83714  
(208) 375-4073  
HERITAGE SERVICE GROUP  
1532 RIVER OAKS WEST  
NEW ORLEANS, LA 70123  
(504) 734-8864  
(800) 499-2351  
(504) 733-2559 FAX  
CONES REPAIR SVC.  
1056 27TH AVENUE SW  
CEDAR RAPIDS, IA 52404  
(319) 365-3325  
GEORGIA  
FAX: (208) 375-4402  
GCS SERVICE INC  
ATLANTA, GA  
ILLINOIS  
800-747-3326  
(770) 452-7322  
800-334-3599  
FAX: (770) 452-7473  
CONES REPAIR SVC.  
2408 40TH AVE.  
MOLINE, IL 61265  
(309) 797-5323  
800-716-7070  
FAX: (309)797-3631  
[email protected]  
FAX: (319) 365-0885  
MAINE  
KANSAS  
GCS SERVICE INC.  
CHELSEA, MA  
(617) 889-9393  
800-225-1155  
FAX: (617) 889-1222  
HERITAGE FOODSERVICE  
GROUP OF ATLANTA  
2100 NORCROSS PKWY.  
SUITE 130  
GCS SERVICE INC.  
KANSAS CITY, MO  
(816) 920-5999  
800-229-6477  
NORCROSS, GA 30071  
(770) 368-1465  
866-388-9837  
EICHENAUER SERVICES INC.  
130 S OAKLAND ST.  
DECATUR, IL 62522  
(217) 429-4229  
800-252-5892  
FAX: (217) 429-0226  
[email protected]  
FAX: (816) 920-7387  
MASSACHUSETTS RESTAU-  
RANT SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868-1930  
GENERAL PARTS, INC.  
1101 E. 13TH STREET  
KANSAS CITY, MO 64106  
(816) 421-5400  
FAX: (866) 388-9838  
WHALEY FOODSERVICE  
REPAIRS  
(800) 279-9967  
800-338-6737  
109-A OWENS INDUSTRIAL  
DRIVE  
SAVANNAH, GA 31405  
(912) 447-0827  
(816) 421-1270 FAX  
FAX: (617) 686-5331  
GCS SERVICE INC.  
ELMHURST, IL  
(630) 941-7800  
KENTUCKY  
PINE TREE FOOD EQUIP-  
MENT  
888-765-0036  
FAX: (912) 447-0826  
800-942-9689  
FAX: (630) 941-6048  
CERTIFIED SERVICE CENTER  
127 DISHMAN LANE  
BOWLING GREEN, KY 42101  
(270) 783-0012  
(877) 907-0012  
FAX: (270) 783-0058  
175 LEWISTON ROAD  
GRAY, ME 04039  
(207) 657-6400  
(800) 540-5427  
(207) 657-5464 FAX  
PIERCE PARTS & SERVICE  
2422 ALLEN ROAD  
MACON, GA 31216  
(478) 781-6003  
GCS SERVICE INC.  
ST. LOUIS, MO  
(314) 683-7444  
800-284-4427  
MARYLAND  
800-368-2512  
FAX: (478) 781-7186  
FAX: (314) 638-0135  
CERTIFIED SERVICE CENTER  
RAMCO BUSINESS PARK  
4283 PRODUCE ROAD  
LOUISVILLE, KY 40218  
(502) 964-7007  
EMR SERVICE DIVISION  
700 EAST 25TH STREET  
BALTIMORE, MD 21218  
(410) 467-8080  
GENERAL PARTS, INC.  
248 JAMES STREET  
BENSONVILLE, IL 60106  
(630) 595-3300  
800-637-6350  
800-879-4994  
(800) 880-3604  
FAX: (630)595-0006  
FAX: (502) 964-7202  
[email protected]  
[email protected]  
FAX: (410) 467-4191  
[email protected]  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
57  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
MARYLAND TO NEW YORK  
EMR SERVICE DIVISION  
106 WILLIAMSPORT CIRCLE  
SALISBURY, MD 21804  
(410) 543-8197  
MICHIGAN  
GCS SERVICE INC.  
ST. LOUIS, MO  
(314) 638-7444  
NEW HAMPSHIRE  
GCS SERVICE INC.  
LIVONIA, MI  
GCS SERVICE INC.  
CHELSEA, MA  
800-284-4427  
888-687-8080  
FAX: (410) 548-4038  
[email protected]  
(248) 426-9500  
800-772-2936  
FAX: (248) 426-7555  
FAX: (314) 638-0135  
(617)889-9393  
800-225-1155  
FAX: (617) 889-1222  
KAEMMERLIN PARTS & SVC.  
2728 LOCUST STREET  
ST. LOUIS, MO 63103  
(314) 535-2222  
FAX: (314) 535-6205  
[email protected]  
EMR SERVICE DIVISION  
5316 Sunnyside Ave.  
Beltsville, MD 20715  
(301) 931-7000  
ACE SERVICE CO.  
95 HAMPTON AVE.  
NEEDHAM, MA 02494  
(781) 449-4220  
800-225-4510 MA & NH  
FAX: (781) 444-4789  
[email protected]  
JACKSON SERVICE COMPA-  
NY  
3980 BENSTEIN RD.  
COMMERCE TWSHP, MI 48382  
(248) 363-4159  
800-348-2365  
FAX: (301) 931-3060  
[email protected]  
GCS SERVICE INC.  
SILVER SPRING, MD  
(301) 585-7550 (DC)  
(410) 792-0338 (BALT)  
(800) 638-7278  
800-332-4053  
FAX: (248) 363-5448  
GENERAL PARTS, INC.  
1101 EAST 13TH STREET  
KANSAS CITY, MO 64106  
(816) 421-5400  
(800) 279-9967  
(816) 421-1270 FAX  
MASSACHUSETTS RESTAU-  
RANT SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868-1930  
GCS SERVICE INC.  
GRAND RAPIDS, MI  
(616) 241-0200  
FAX: (301) 495-4410  
800-823-4866  
FAX: (616) 241-0541  
MONTANA  
800-338-6737  
MASSACHUSETTS  
FAX: (617) 868-5331  
MINNESOTA  
RESTAURANT APPLIANCE  
SVC.  
ACE SERVICE CO.  
95 HAMPTON AVE.  
NEEDHAM, MA 02494  
(781) 449-4220  
800-225-4510 MA & NH  
FAX: (781) 444-4789  
[email protected]  
NEW JERSEY  
GCS SERVICE INC.  
MINNEAPOLIS, MN  
(612) 546-4221  
800-345-4221  
FAX: (612) 546-4286  
7219 ROOSEVELT WAY NE  
SEATTLE, WA 98115  
(206) 524-8200  
800-433-9390  
FAX: (206) 525-2890  
[email protected]  
JAY HILL REPAIRS  
90 CLINTON RD.  
FAIRFIELD, NJ 07004  
(973) 575-9145  
800-836-0643  
FAX: (973) 575-5890  
[email protected]  
MASSACHUSETTS RESTAU-  
RANT SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868-1930  
GENERAL PARTS, INC.  
11311 HAMPSHIRE AVENUE  
SOUTH  
BLOOMINGTON, MN 55438-  
2456  
NEBRASKA  
GOODWIN - TUCKER GROUP  
7535 D STREET  
OMAHA, NE 68124  
(402) 397-2880  
GCS SERVICE INC.  
EAST RUTHERFORD, NJ  
(973) 614-0003  
800-338-6737  
(952) 944-5800  
800-399-8294  
FAX: (617) 868-5331  
(800) 279-9980  
800-228-0342  
FAX: (973) 614-0230  
(800) 279-9980 FAX  
FAX: (402) 397-2881  
[email protected]  
GCS SERVICE INC.  
CHELSEA, MA  
(617) 889-9393  
GCS SERVICE INC.  
PHILADELPHIA, PA  
(215) 925-6217  
MISSISSIPPI  
NEVADA  
800-225-1155  
FAX: (617) 889-1222  
GCS SERVICE INC.  
JACKSON, MS  
(601) 956-7800  
800-441-9115  
FAX: (215) 925-6208  
HI TECH COMMERCIAL SER-  
VICE  
GCS SERVICE INC.  
HARTFORD, CT  
(860) 549-5575  
800-723-1562  
FAX: (860) 527-6355  
800-274-5954  
FAX: (601) 956-1200  
1840 STELLA LAKE STREET  
NORTH LAS VEGAS, NV 89106  
(702) 649-4616  
(877) 924-4832  
FAX: (702) 649-4607  
[email protected]  
ELMER SCHULTZ SERVICES  
201 W. WASHINGTON AVE.  
PLEASANTVILLE, NJ 08232  
(609) 641-0317  
800-378-1641  
FAX:(609) 641-8703  
GCS SERVICE INC.  
MEMPHIS, TN  
(901) 366-4587  
SUPERIOR KITCHEN SER-  
VICE INC.  
399 FERRY STREET  
EVERETT, MA 02149  
(617) 389-1899  
800-262-9155  
FAX: (901) 366-4588  
[email protected]  
5454 LOUIE LANE  
RENO, NV 89511  
(775) 852-9696  
NEW YORK  
MISSOURI  
FAX: (775) 852-5104  
APPLIANCE INSTALLATION  
AND SERVICE CORP.  
1336 MAIN STREET  
BUFFALO, NY 14209  
(716) 884-7425  
(888) 590-1899  
(617) 389-1996 FAX  
GCS SERVICE INC.  
KANSAS CITY, MO  
(816) 920-5999  
GCS SERVICE INC.  
LAS VEGAS, NV  
(702) 450-3495  
800-229-6477  
FAX: (816) 920-7387  
800-500-9060  
800-722-1252  
FAX: (702) 450-3491  
FAX: (716) 884-0410  
[email protected]  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
58  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
NEW YORK TO PENNSYLVANIA  
B.E.S.T. INC.  
AUTHORIZED APPLIANCE  
SERVICECENTER  
904 S. MARSHALL ST.  
WINSTON-SALEM, NC 27403  
(336) 725-5396  
OHIO  
OREGON  
3003 GENESEE STREET  
BUFFALO, NY 14225  
(716) 893-6464  
800-338-5011  
FAX: (716) 893-6466  
[email protected]  
CERTIFIED SERVICE CENTER  
890 REDNA TERRACE  
CINCINNATI, OH 45215  
(513) 772-6600  
RON'S SERVICE  
16364 SW 72ND AVE  
PORTLAND, OR 97224  
(503) 624-0890  
FAX:(336) 721-1289  
800-543-2060  
800-851-4118  
AUTHORIZED APPLIANCE  
SERVICECENTER  
104 HINTON AVE.  
WILMINGTON, NC 28403  
(910) 313-1250  
FAX:(910) 313-6130  
FAX: (513) 612-6600  
[email protected]  
FAX: (503) 684-6107  
[email protected]  
DUFFY'S EQUIPMENT SVC.  
3138 ONEIDA STREET  
SAUQUOIT, NY 13456  
(315) 737-9401  
800-443-8339  
FAX: (315) 737-7132  
[email protected]  
CERTIFIED SERVICE CENTER  
171J-K NORTH HAMILTON RD.  
COLUMBUS, OH 43213  
(614) 751-3769  
(866) 862-1252  
FAX: (614) 751-5792  
PENNSYLVANIA  
A.I.S. COMMERCIAL PARTS &  
SERVICE  
1816 WEST 26TH STREET  
ERIE, PA 16508  
(814) 456-3732  
800-332-3732  
WHALEY FOODSERVICE  
8334-K ARROWRIDGE BLVD  
CHARLOTTE, NC 28273  
(704) 529-6242  
FAX: (704) 529-1558  
[email protected]  
NORTHERN PARTS & SVC.  
21 NORTHERN AVENUE  
PLATTSBURGH, NY 12903  
(518) 563-3200  
800-634-5005  
FAX: (800) 782-5424  
[email protected]  
[email protected]  
CERTIFIED SERVICE CENTER  
6025 N. DIXIE DRIVE  
DAYTON, OH 45414  
(937) 898-4040  
(800) 257-2611  
FAX: (937) 898-4177  
[email protected]  
FAX: (814) 452-4843  
[email protected]  
WHALEY FOODSERVICE  
REPAIRS  
203-D CREEK RIDGE RD.  
GREENSBORO, NC 27406  
(336) 333-2333  
ELMER SCHULTZ SVC.  
540 NORTH 3RD STREET  
PHILADELPHIA, PA 19123  
(215) 627-5400  
FAX: (215) 627-5408  
[email protected]  
GCS SERVICE INC.  
BROOKLYN, NY  
(718) 486-5220  
FAX: (336) 333-2533  
[email protected]  
COMMERCIAL PARTS & SVC.  
OF COLUMBUS  
800-969-4271  
FAX: (718) 486-6772  
5033 TRANSAMERICA DRIVE  
COLUMBUS, OH 43228  
(614) 221-0057  
800-837-8327  
FAX: (614) 221-3622  
GCS SERVICE INC.  
PHILADELPHIA, PA  
(215) 925-6217  
800-441-9115  
FAX: (215) 925-6208  
WHALEY FOODSERVICE  
REPAIRS  
335-105 SHERWEE DRIVE  
RALEIGH, NC 27603  
(919) 779-2266  
ALL SERVICE KITCHEN  
EQUIPMENT REPAIR  
10 CHARLES ST.  
NEW HYDE PARK, NY 11040  
(516) 378-1176  
FAX: (919) 779-2224  
[email protected]  
GCS SERVICE INC.  
COLUMBUS, OH  
(614) 476-3225  
GCS SERVICE INC.  
HARRISBURG, PA  
(717) 564-3282  
FAX: (516) 378-1735  
ALL ISLAND REPAIRS  
40-9 BURT DRIVE  
DEER PARK, NY 11729  
(631) 242-5588  
WHALEY FOODSERVICE  
REPAIRS  
6418-101 AMSTERDAM WAY  
WILMINGTON, NC 28405  
(910) 791-0000  
800-282-5406  
FAX: (614) 476-1196  
800-367-3225  
FAX: (717) 564-9286  
ELECTRICAL APPLIANCE  
REPAIR SVC.  
5805 VALLEY BELT ROAD  
CLEVELAND, OH 44131  
(216) 459-8700  
GCS SERVICE INC.  
PITTSBURGH, PA  
(412) 787-1970  
800-738-1221  
FAX: (412) 787-5005  
FAX: (631) 242-6102  
FAX: (910) 791-6662  
[email protected]  
NORTH CAROLINA  
AUTHORIZED APPLIANCE  
SERVICECENTER  
1020 TUCKASEEGEE RD.  
CHARLOTTE, NC 28208  
(704) 377-4501  
NORTH DAKOTA  
800-621-8259  
FAX: (216) 459-8707  
[email protected]  
K & D PARTS AND SERVICE  
CO.  
1833-41 N CAMERON STREET  
HARRISBURG, PA 17103  
(717) 236-9039  
GCS SERVICE INC.  
MINNEAPOLIS, MN  
(612) 546-4221  
OKLAHOMA  
(800) 532-6127  
800-345-4221  
FAX:(704) 377-4504  
FAX: (612) 546-4286  
HAGAR RESTAURANT EQMT.  
1229 W MAIN STREET  
OKLAHOMA CITY, OK 73106  
(405) 235-2184  
800-445-1791  
FAX: (405) 236-5592  
800-932-0503  
FAX: (717) 238-4367  
[email protected]  
AUTHORIZED APPLIANCE  
SERVICECENTER  
800 N. PERSON ST.  
RALEIGH, NC 27604  
(919) 834-3476  
GENERAL PARTS, INC.  
10 SOUTH 18TH STREET  
FARGO, ND 58103  
(701) 235-4161  
CLARK SERVICE & PARTS  
306 AIRPORT DRIVE  
BOX 10  
(800) 279-9987  
FAX:(919) 834-3477  
(701) 235-0539 FAX  
SMOKETOWN, PA 17576  
(717) 392-5590  
(717) 392-5735  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
59  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
RHODE ISLAND TO WISCONSIN  
RHODE ISLAND  
WHALEY FOODSERVICE  
REPAIRS  
4740-A FRANCHISE STREET  
N. CHARLESTON, SC 29418  
(843) 760-2110  
GCS SERVICE INC.  
HOUSTON, TX  
(713)785-9187  
800-868-6957  
FAX: (713) 785-3979  
GCS SERVICE INC.  
VIRGINIA BEACH, VA  
(757) 464-3500  
800-476-4278  
FAX: (757) 464-4106  
GCS SERVICE INC.  
EAST PROVIDENCE, RI  
(401) 434-6803  
800-462-6012  
FAX: (843) 760-2255  
FAX: (401) 438-9400  
[email protected]  
GCS/STOVE PARTS  
2120 SOLANA STREET  
FORT WORTH, TX 76117  
(817) 831-0381  
WASHINGTON  
SUPERIOR KITCHEN SER-  
VICE INC.  
SOUTH DAKOTA  
GCS SERVICE INC.  
SEATTLE, WA  
669 ELMWOOD AVENUE  
PROVIDENCE, RI 02907  
(888) 590-1899  
GCS SERVICE INC.  
MINNEAPOLIS, MN  
(612) 546-4221  
800-433-1804  
FAX: (817) 834-7754  
[email protected]  
(206) 763-0353  
800-211-4274  
FAX: (206) 763-5943  
(401) 781-1996 FAX  
800-345-4221  
FAX: (612) 546-4286  
UTAH  
RESTAURANT APPLIANCE  
SERVICE  
SOUTH CAROLINA  
GENERAL PARTS, INC.  
10 SOUTH 18TH STREET  
FARGO, ND 58103  
(701) 235-4161  
LA MONICA'S RESTAURANT  
EQMT. SVC.  
6182 SOUTH STRATLER  
AVENUE  
7219 ROOSEVELT WAY, NE  
SEATTLE, WA 98115  
(206) 524-8200  
AUTHORIZED APPLIANCE  
SERVICECENTER  
1811 TAYLOR ST.  
800-433-9390  
COLUMBIA, SC 29202  
(803) 254-8414  
(800) 279-9987  
(701) 235-0539 FAX  
MURRAY, UT 84107  
(801) 263-3221  
FAX: (206) 525-2890  
[email protected]  
FAX: (803) 254-5146  
800-527-2561  
TENNESSEE  
FAX: (801) 263-3229  
[email protected]  
WEST VIRGINIA  
AUTHORIZED APPLIANCE  
SERVICECENTER  
2249 AUGUSTA RD.  
GREENVILLE, SC 29605  
(864) 235-9616  
GCS SERVICE INC.  
MEMPHIS, TN  
(901) 366-4587  
800-262-9155  
FAX: (901) 366-4588  
STATEWIDE SERVICE, INC.  
603 MAIN AVE.  
NITRO, WV 25143  
(304) 755-1811  
(800) 441-9739  
FAX: (304) 755-4001  
[email protected]  
VERMONT  
NORTHERN PARTS & SVC.  
4874 S. CATHERINE STREET  
PLATTSBURGH, NY 12901  
(518) 563-3200  
800-634-5005  
FAX: (800) 782-5424  
FAX: (864) 235-9623  
WHALEY FOODSERVICE  
REPAIRS  
I 26&US1  
GCS SERVICE INC.  
NASHVILLE, TN  
(615) 244-8050  
WISCONSIN  
P.O. BOX 4023  
800-831-7174  
[email protected]  
WEST COLUMBIA, SC 29170  
(803) 791-4420  
800-877-2662  
FAX: (803) 794-4630  
[email protected]  
FAX: (615) 244-8885  
APPLIANCE SERVICE CEN-  
TER, INC.  
2439 ATWOOD AVE  
MADISON, WI 53704  
(608) 246-3160  
GCS SERVICE INC.  
CHELSEA, MA  
(617)889-9393  
800-225-1155  
FAX: (617) 889-1222  
TEXAS  
ARMSTRONG REPAIR CEN-  
TER  
800-236-7440  
WHALEY FOODSERVICE  
REPAIRS  
748 CONGAREE ROAD  
GREENVILLE, SC 29607  
(864) 234-7011  
800-494-2539  
FAX: (864) 234-6662  
[email protected]  
5110 GLENMOUNT DRIVE  
HOUSTON, TX 77081  
(713) 666-7100  
800-392-5325  
FAX: (713) 661-0520  
[email protected]  
FAX: (608) 246-2721  
[email protected]  
VIRGINIA  
DAUBERS, INC.  
APPLIANCE SERVICE  
CENTER, INC.  
6843 W. BELOIT RD.  
WEST ALLIS, WI 53219  
(414) 543-6460  
800-236-6460  
FAX: (414) 543-6480  
[email protected]  
7645 DYNATECH COURT  
SPINGFIELD, VA 22153  
(703) 866-3600  
800-554-7788  
FAX: (703) 866-4071  
[email protected]  
COMMERCIAL KITCHEN  
REPAIR CO.  
1377 N BRAZOS  
WHALEY FOODSERVICE  
REPAIRS  
P.O BOX 831128  
1406-C COMMERCE PL.  
MYRTLE BEACH, SC 29577  
(843) 626-1866  
FAX: (843) 626-2632  
[email protected]  
SAN ANTONIO, TX 78207  
(210) 735-2811  
800-292-2120  
FAX: (210) 735-7421  
[email protected]  
GCS SERVICE INC.  
SILVER SPRING, MD  
(301) 585-7550(DC)  
(410) 792-0388(BALT)  
800-638-7278  
APPLIANCE SERVICE  
CENTER  
786 MORRIS AVE  
GREEN BAY, WI 54304  
(920) 496-9993  
FAX: (301)495-4410  
GCS SERVICE INC.  
DALLAS, TX  
(972) 484-2954  
800-442-5026  
800-236-0871  
FAX: (920) 496-9927  
[email protected]  
GCS SERVICE INC.  
RICHMOND, VA  
(804) 672-1700  
FAX: (972) 484-2531  
800-899-5949  
FAX: (804) 672-2888  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
60  
 
SECTION 7: JACKSON MAINTENANCE & REPAIR CENTERS  
WISCONSIN TO WYOMING/INTERNATIONAL  
GENERAL PARTS, INC.  
W223 N735 SARATOGA DRIVE  
WAUKESHA, WI 53186  
(262) 650-6666  
(800) 279-9946  
(262) 650-6660 FAX  
WYOMING  
HAWKINS COMMERCIAL  
APPLIANCE SERVICE  
3000 S. WYANDOT ST.  
ENGLEWOOD, CO 80110  
(303) 781-5548  
(800) 624-2117  
FAX: (303) 761-5561  
[email protected]  
METRO APPLIANCE SERVICE  
1640 S BROADWAY  
DENVER, CO 80210  
(303) 778-1126  
800-525-3532  
FAX: (303) 778-0268  
[email protected]  
INTERNATIONAL  
GLOBAL PARTS AND SUPPLY  
7758 NW 72ND ST  
MIAMI, FL 33166  
(305) 885-6353  
H.D. SHELDON AND CO  
19 UNION SQUARE, WEST  
NEW YORK, NY 10003  
(212) 627-1759  
(212) 924-6920  
CANADA  
THE GARLAND GROUP  
1177 KAMATO ROAD  
MISSISSAUGA, ONTARIO L4W  
1X4  
(905) 206-8380  
SALES  
(905) 624-1419  
FAX: (905) 624-1851  
SERVICE  
800-427-6668  
FAX: 800-361-7745  
July 24, 2009  
Tempstar LT/NB/S Technical Manual 7610-003-61-42 B  
Issued: 10-08-2008 Revised: N/A  
61  
 
SERIAL NUMBER:  
MODEL: Tempstar  
An  
Company  
208-230-460 Volt/60 Hz/3 Phase  
F RISE BOOSTER 208V 230V  
40  
460V  
OPERATING PARAMETERS  
WASH MOTOR  
WASH HEATER  
RINSE HEATER  
3/4 HP 5.7A 3/4 HP 5.7A 3/4 HP 1.8 A  
4.1 KW 11.4A 5 KW 12.6A 5 KW 6.3 A  
9 KW 25.0 A 11 KW 27.2A 11KW 13.8A  
MINIMUM WASH TEMPERATURE  
MINIMUM RINSE TEMPERATURE  
150  
180  
F
F
TOTALLOAD  
42.1 A  
45.5A  
21.9A  
MINIMUM INCOMING WATER TEMPERATURE  
70  
40  
F
F
RISE BOOSTER  
RISE BOOSTER  
110  
140  
F  
F
70  
F RISE BOOSTER  
208V  
230V  
460V  
WASH MOTOR  
WASH HEATER  
RINSE HEATER  
3/4 HP 5.7A 3/4 HP 5.7A 3/4 HP 1.8 A  
4.1 KW 11.4A 5 KW 12.6A 5 KW 6.3 A  
10.5 KW 29.1 A 12.9 KW 32.4A 12.9 KW 16.2A  
WASH CYCLE TIME  
RINSE CYCLE TIME  
FLOW PRESSURE  
45 SEC  
11 SEC  
10 PSI  
TOTALLOAD  
46.2 A  
50.7A  
24.3A  
208-230 Volt/60 Hz/1 Phase  
40F RISE BOOSTER 208V 230V  
WASH MOTOR  
WASH HEATER  
RINSE HEATER  
3/4 HP 5.7A 3/4 HP 5.7A  
4.1 KW 19.7 A 5 KW 21.7A  
9 KW 43.3 A 11 KW 47.8A  
TOTALLOAD  
68.7 A  
75.2A  
Made in the USA  
70  
F RISE BOOSTER  
208V  
230V  
Jackson MSC Inc.  
P.O. Box 1060  
Barbourville, KY. 40906  
(606) 523-9795  
WASH MOTOR  
WASH HEATER  
RINSE HEATER  
3/4 HP 5.7A 3/4 HP 5.7A  
4.1 KW 19.7 A 5 KW 21.7A  
10.5 KW 50.4 A 12.9 KW 56.1A  
Commercial  
Dishwasher  
597G  
TOTALLOAD  
75.8 A  
83.6A  
09905-003-69-11A  
Tempstar units that are manufactured with the above referenced data plate are able  
to be field converted to different phases and voltages. To accomplish this, your unit  
should have shipped with the Tempstar Phase Conversion Kit, part number 06401-  
003-71-71. This kit contains the appropriate decals and schematics to apply to your  
unit once the conversion is complete.  
All work should be performed only by Authorized Jackson Service Agents. A listing of your  
local agents is in the back of your installation manual.  
Steps:  
1.  
Perform the appropriate wiring and component changes as necessary to achieve  
the desired result. Reference Jackson technical manuals or contact technical ser  
vice for assistance.  
2.  
3.  
Verify the Schematic is correct. If not, replace with the correct one from the kit.  
At the power inlet, remove the “Wired For” decal and replace with the one that  
matches the configuration of your machine.  
 
 

Ingersoll Rand Marine Radio CCN 03530515 User Manual
Invacare Humidifier Poseidon User Manual
IRIS Power Supply QP 1800 User Manual
JVC Car Speaker CS HX645 User Manual
JVC Car Stereo System GET0137 001A User Manual
JVC Video Games LT 32EX19 User Manual
Kenwood Stereo Receiver C V301 User Manual
Kettler Table Top Game 07042 790 User Manual
Kicker Speaker DCVR10 User Manual
KitchenAid Refrigerator NL240V User Manual